________________________________________________________________________________
John Deere 4066M Attachments
John Deere 4066M Front End Loader
D170 Loader Specifications
Type of Attachment - Front End Loader
Compatibility - JD 4066M
Lift capacity at pivot pin (max. ht.) - 2,391 lb. (1087 kg)
Lift capacity at 500 mm ahead of pivot pin - 1,760 lb. (800 kg)
Lift capacity to 59 in. at pivot pin - 2,875 lb. (1307 kg)
Lift capacity to 59 in. at 500 mm ahead - 2.295 lb. (1043 kg)
Max. lift height at pivot pin - 112.1 in. (2850 kg)
Reach at max. height - 28 in. (705 mm)
Breakout force at pivot pin - 3,853 lb. (1743 kg)
Breakout force at 500mm - 2,902 lb. (1315 kg)
Dump angle - 42 deg.
Rollback angle - 28.6 deg.
Loader raising/lowering time - 4.26/3.13 sec.
Bucket dump time/regen - 3.14 sec.
Bucket rollback time - 2.42 sec.
Operate D170 Loader with
Multi-Function Lever
Lever Movement - Forward. Loader Operation - Boom Lower.
Lever Movement - Locked Forward. Loader Operation - Boom Float.
Lever Movement - Forward, 45° to Right-Hand Side. Loader Operation -
Boom Lower, Bucket Dump.
Lever Movement - To Right-Hand Side. Loader Operation - Bucket Dump.
Lever Movement - Back, 45° to Right-Hand Side. Loader Operation - Boom
Raise, Bucket Dump.
Lever Movement - Back. Loader Operation - Boom Raise.
Lever Movement - To Left-Hand Side. Loader Operation - Bucket Roll Back.
Lever Movement - Forward, 45° to Left-Hand Side. Loader Operation - Boom
Lower, Bucket Roll Back.
Lever Movement - Pull Knob Out. Loader Operation - Lock Out Control
Lever.
H180 Loader Specifications
Type of Attachment - Front End Loader
Loader Type - Non Self-Leveling (NSL)
Compatibility - JD 4066M
Bucket Width - 1850 mm (73 in.)
Bucket Length - 585 mm (23 in.)
Bucket Mass - 146 kg (321 lb.)
Hydraulic System Rated Flow - 60 L/min. (16 gpm)
Hydraulic Maximum Pressure - 17238 kPa (172 bar) (2500 psi)
Lift Height (Maximum) To Pivot Pin - 2799 mm (110 in.)
Bucket Level Clearance - 2593 mm (102 in.)
Bucket Dumped Clearance - 2195 mm (86 in.)
Overall Length - 3549 mm (140 in.)
Digging Depth - 119 mm (5 in.)
Reach At Maximum Lift Height with Bucket Dumped - 753 mm (30 in.)
Bucket Reach on Ground with Bucket Leveled - 1703 mm (67 in.)
Dump Bucket Angle - 47°
Dump Bucket Angle at Ground - 130°
Rollback Bucket Angle - 33°
Overall Height In Carry Position - 1535 mm (60 in.)
Lift Capacity To Maximum Height at Pivot Point - 1154 kg (2539 lb.)
Lift Capacity To Maximum Height - 857 kg (1885 lb.)
Lift Capacity To 1500 mm (59 in.) at pivot pin - 1374 kg (3023 lb.)
Lift Capacity To 1500 mm (59 in.) - 1097 kg (2413 lb.)
Breakout Force At Pivot Point - 17913 N
Breakout Force At 500 mm forward of pivot point - 13508 N
Bucket Rollback Force At maximum height - 9221 N
Bucket Rollback Force At 1500 mm (59 in) lift height - 14627 N
Bucket Rollback Force At Ground Level Line - 15245 N
Loader Raise Time - 2.61 sec.
Loader Lower Time - 1.75 sec.
Bucket Dump Time - 1.96 sec.
Bucket Rollback Time - 1.16 sec.
Round Bale Sizes and Weights
Bale Size (Diameter x Length), mm (in.) - Maximum Weight, kg (lbs.) /
Material
Round Bale 1219 x 1219 (48 x 48) - 341 (750) / Dry Hay
Round Bale 1524 x 1219 (60 x 48) - 499 (1100) / Dry Hay
Round Bale 1524 x 1219 (60 x 48) - 795 (1750) / Silage
Round Bale 1524 x 1524 (60 x 60) - 658 (1450) / Dry Hay
Round Bale 1829 x 1219 (72 x 48) - 729 (1650) / Dry Hay
Round Bale 1829 x 1219 (72 x 48) - 999 (2200) / Silage
Round Bale 1829 x 1524 (72 x 60) - 999 (2200) / Dry Hay
Required Minimum Tractor Ballast
- H180 MSL: 1600 mm (63 in.) or greater rear tread setting. Rear tires
filled with liquid ballast. Four rear wheel weights. 380 kg (836 lb)
minimum 3-point hitch ballast. H180 NSL: 1600 mm (63 in.) or greater
rear tread setting. Rear tires filled with liquid ballast. No rear wheel
weights 380 kg (836 lb) minimum 3-point hitch ballast. For fluid filled
rear tires: Fill tires 3/4 full using a calcium chloride mixture of 1.6
kg (3.5 lb) per 4 L (1 U.S. gal) of water.
John Deere 4066M Snowblower
80" Snowblower Specifications
Model - Frontier SB1280
Snow blower Type - Rear Mount
Compatibility - JD 4066M
Hitch compatibility - Cat. 1 and Cat. 2 iMatch and Quick Hitch
Steel skid shoes - Adjustable and replaceable
Cutting edge - Bolt on/reversible
Park Stand - Standard
Chute type - Three part
Chute deflector - Hydraulic standard
Chute rotation - Hydraulic 260 degrees
Working height - 31 in. (78.7 cm)
Transport width - 80.5 in. (204.5 cm)
Working width - 80.5 in. (204.5 cm)
Length - 49 in. (124.5 cm)
Roller chain - #60H
Chain idler adjustment - Automatic
Chute diameter - 10.5 in. (26.7 cm)
Auger diameter - 20 in. (50.8 cm)
Auger speed - 200 RPM
Impeller speed - 540 RPM
Impeller blades - 4
Impeller diameter - 26 in. (66 cm)
Tractor PTO speed - 540 RPM
Minimum tractor HP - 35 PTO HP
Maximum tractor HP - 80 PTO HP
Auger overload protection - Shearbolt
PTO overload protection - Shearbolt
Operating weight3 - 1090 lb. (494.4 kg)
SB1280 Snowblower Troubleshooting
Auger and fan do not turn - Check if an object is
blocking the fan or auger. Check that PTO is engaged. Check for oil
leaks. Check if pump is in recirculation mode. Check hydraulic pump oil
level and add some if needed. Check that the input and output hoses are
connected. Check that the input and output hoses are in the right
position, if not reverse their position. Check if the flow restrictor is
obstructed and replace if needed.
Auger and fan are turning in reverse - Check that the
hoses are connected correctly to the hydraulic manifold and reverse
their position if necessary.
Snow is not being ejected from the chute - Check if the
snow output is obstructed, unclog with a 36" stick.
80-inch Snow blower clogs up easily - Check the
viscosity of the hydraulic oil. Check hydraulic pump oil level and add
some if needed. Check if the tractor engine is at full RPM. Check the
hydraulic pressure of the system. Check the hydraulic flow of the
system. Check if the flow restrictor is obstructed and replace if
needed. Check if the sequence valve is working and adjust or replace if
needed.
John Deere 4066M Blade
96-inch Rear Blade Specifications
Models - Frontier RB2196
Type - Rear Mount
Compatibility - JD 4066M
Hitch - Cat. 1 iMatch
Frame - Formed steel channel frame
Cutting edge - 1/2" x 6" (1.26 x 15.1 cm) reversible
Angle/Pivot - 360 Degrees
Angle-Forward - 3, up to 53 degrees each side
Angle-Reverse - 3, up to 53 degrees each side
Moldboard thickness - 1/4" (0.63 cm)
Moldboard length - 96" (242 cm)
Moldboard height - 17" (42.9 cm)
Moldboard type - Progressive-formed
Moldboard upperedge - Full bend
Offset (or swing) - 6" or 12" (15.1 or 30.2 cm) left or right
Tractor maximum - 65 HP
Tilt - 3, up to 22 degrees up and down
Operating weight - 476 lbs. (216 kg)
John Deere 4066M Rotary Cutter
RC2072 Rotary Cutter Specifications
Model - Frontier RC2072
Compatibility - JD 4066M
Cutting width - 6 ft. (1.8 m)
Cutting height - 1.5 to 9 in. (38 to 229 mm)
Overall width - 6 ft. 4 in. (1.9 m)
Overall length - 9 ft. 3 in. (2.8 m)
Body depth - 7.5 in. (191 mm)
Deck thickness - 0.11 in. (3 mm)
Skirt thickness - 11 gauge (3 mm)
Driveline protection - Choice of shear bolt or self-adjusting slip
clutch
Gearcase power rating - 65 hp (48.5 kW)
Bladeholder - Round pan
Blades - Suction, 0.5x3 in. (13x76 mm)
Blade-tip speed - 540 rpm/14,955 ft./min. (76 m/s)
Brush cutting capacity - 1 in. (25 mm)
Hitch category - Cat. 1
Minimum tractor PTO power - 25 hp (18.6 kW)
Weight - 709.6 lb. (321.9 kg)
Checking Driveline/Cutter Clearance
- Raise RC2072 Rotary Cutter slowly and check for clearance between
driveline shield and cutter deck. Check clearance between tractor tires
and footguards or chain guard. Check to see if hitch height position
will provide clearance desired. Shorten center link or lengthen lift
links to provide clearance. Raise and lower RC2072 cutter slowly to
check for binding or interference. Check cutter-to-tractor driveline
telescoping length to ensure it does not bottom out. Modify driveline if
necessary.
Disassembling and Assembling
Driveline Shields - Separate telescoping parts. Remove
driveline shield screw. Rotate cone to align tab with hole and slide
shield rearward off of driveline. Assemble in reverse order.
________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________