________________________________________________________________________________

John Deere 410G Backhoe Specs

John Deere 410G Engine

Engine Model - John Deere 4045T
Engine Type - In-line, 4-Cycle
Number of cylinders - 4
Displacement, L (cu in) - 4.5 (275)
Bore and Stroke, mm (in) - 106 x 127 (4.17 x 5.00)
Compression Ratio - 19.0:1
Aspiration - Turbocharged
Net peak power - 96 hp (71.3 kW) @ 2,100 rpm
Net peak torque - 279 lb.-ft. (378 Nm) @ 1,400 rpm
Torque rise - 23 percent
Fuel Pump - High-Pressure Common Rail
Cylinder Head - 2-Valve
Exhaust Manifold - Watercooled
Cylinder Liners - Wet-Type Replaceable
Oil Filter - Remote Access
Oil Tank - Oil Fil and Dipstick Combinations
Fuel System - Mechanical Governor
Heat Exchanger - Standard
Keel Cooled - Optional
Low Idle Speed - 700
Fuel Consumption - 26.3-29.7 L/h (6.9-7.8 g/h)
Length, mm (in) - 867 (34.1)
Width, mm (in) - 680 (26.8)
Height, mm (in) - 1055 (41.5)
Weight dry, kg (lb) - 491 (1082)

John Deere 410G Drivetrain

Transmission Type - Four-speed, helical cut gear, full powershift transmission with hydraulic reverser
Gears - 4 forward and 3 reverse
Oil capacity - 16 qts (15.1 L)
Chassis - 2WD / 4WD (optional)
Front axle model - Carraro
Front axle type - Non-powered
Service brakes - Power-assisted hydraulic, wet multi-disc, self adjusting
Parking brake - electric switch control, hydraulically released wet multi-disc / Independent of service brakes
Steering - Hydrostatic power steering with emergency manual mode
MFWD Differential - limited-slip

JD 410G Hydraulic System

Hydraulic System - Pressure compensated load sensing (PCLS)
Pressure (Backhoe) - 3,625 psi (25 000 kPa)
Pressure Loader - 3,625 psi (25 000 kPa)
Flow @ 2,200 rpm Backhoe/Loader - 43 gpm (163 L/min.)
Hydraulic reservoir - Independent

John Deere 410G Backhoe Specifications

Loading height, truck loading position (Standard Backhoe) - 12 ft. 6 in. (3.81 m)
Loading height, truck loading position (Dipperstick Extended) - 15 ft. 6 in. (4.72 m)
Reach from center of swing pivot (Standard Backhoe) - 19 ft. 8 in. (5.99 m)
Reach from center of swing pivot (Dipperstick Extended) - 23 ft. 8 in. (7.21 m)
Reach from center of rear axle (Standard Backhoe) - 23 ft. 4 in. (7.11 m)
Reach from center of rear axle (Dipperstick Extended) - 27 ft. 4 in. (8.33 m)
Maximum digging depth (Standard Backhoe) - 15 ft. 10 in. (4.83 m)
Maximum digging depth (Dipperstick Extended) - 20 ft. (6.10 m)
Ground clearance, minimum - 14 in. (356 mm)
Transport height (Standard Backhoe) - 12 ft. 11 in. (3.94 m)
Transport height (Dipperstick Extended) - 12 ft. 10 in. (3.91 m)
Overall length, transport - 23 ft. 11 in. (7.29 m)
Stabilizer width – transport with ROPS - 7 ft. 6 in. (2.30 m)
Stabilizer spread – operating - 11 ft. 4 in. (3.45 m)
Stabilizer overall width - 13 ft. 3 in. (4.03 m)
Width over tires - 84.6 in. (2.18 m)
Height to tops of ROPS - 9 ft. 3 in. (2.82 m)
Length from axle to axle - 82.7 in. (2100 mm)

John Deere 410G Loader Specifications

Height to bucket hinge pin, maximum - 11 ft. (3.35 m)
Dump clearance, bucket at 45 degrees - 8 ft. 4 in. (2.49 m)
Reach at full height, bucket at 45 degrees - 35.5 in. (902 mm)
Digging depth below ground, bucket level - 4.2 in. (107 mm)
Distance from front axle centerline to bucket cutting edge - 82.6 in. (2097 mm)
Raising time to full height - 4.6 sec
Bucket dump time at maximum height - 1.4 sec
Bucket lowering time (power down) - 2.4 sec

Tires

Front Tires - 11L-16
Front Tires - 12.5/80-18 / 14.5/75-16.1
Rear Tires - 19.5L-24
Rear Tires - 21L-24

JD 410G Dimensions

Operating Weight (2WD ROPS) - 15,000 lbs (6804 kg)
Operating Weight (4WD, cab, extentable dipperstick) - 18,500 lbs (8391 kg)
Wheelbase - 82.7 inches (210 cm)
Length - 287 inches (728 cm)
Width - 90 inches (228 cm)
Height (ROPS) - 111 inches (281 cm)
Height (cab) - 111 inches (281 cm)
Turning radius with brakes - 13 ft. 3 in. (4.04 m)
Bucket clearance circle - 31 ft. 8 in. (9.65 m)
Steering wheel turns, lock to lock - 3.3
Ground clearance - 14 inches (35 cm)