________________________________________________________________________________

Kubota B2150 Troubleshooting

Kubota B2150 Diesel Engine Troubleshooting

Engine difficult to start or will not start: Fuel filter plugged. Change the filter element. Air in the fuel pipes. Bleed the fuel pipes. Clogged injection nozzle. Check injection nozzles and replace if required. Fuel injection pump is defective. Replacement or repair required.

Engine stops suddenly during operation: Improper fuel injection timing. Use the correct fuel injection pump timing adjustment. Fuel filter plugged. Filter maintenance required. Coolant temperature is low. Warm up to required temperature.

Engine starts but stops suddenly: Fuel filter element is dirty. Clean or change the filter. Fuel injection pump is faulty. Rebuild or install a new injection pump. Clogged air filter element. Carry out maintenance on air filter.

Engine overheated: Clogged radiator core or leaking radiator cap. Install new cap or clean radiator. Insufficient coolant fluid. Add coolant fluid and inspect the cooling system for leaks. Broken or loose fan belt. Belt change is required. Engine oil level low. Need to add engine oil.

Engine lacks power: Faulty fuel injection nozzles. Inspect nozzles and replace if necessary. Clogged fuel lines or hoses. Service fuel lines and hoses. Air filter element clogged. Replace air filter element. Damaged cylinder-head gasket. Install new cylinder head gasket.

Engine noise or knocking: Engine is not preheated. Warm up engine as required. Low engine oil level. Checking oil level and add if necessary. Wrong setting of fuel injection pump timing. Set the fuel pump timing correctly. Scored or worn pistons. Replace the pistons as required. Connecting rod is not aligned or defective. Need to change or align the connecting rod.

Engine stops while idling: Low idle speed set incorrectly. Adjust low idling as recommended. The valve clearance is incorrect. Adjust to proper valve clearance. Fuel injection pump is defective. Replacement or repair required.

Low oil pressure: Oil level is insufficient. Add oil to the engine crankcase. Oil pump malfunction. Check and replace if necessary. Oil filter clogging. Clean or change engine oil filter.

Kubota B2150 Transmission Troubleshooting

Transmission makes noise: Gears are defective or backlash is improper. Replace gears or adjust backlash correctly. Worn or bent gear shift forks. Change the shift forks. Damaged or worn shaft splines. Change the shaft. Low fluid level. Checking transmission fluid level and add if necessary. Bearings are damaged or worn. Change faulty bearings. Transmission oil is contaminated. Fill up with fresh transmission oil.

Hard to shift gears: Corroded or worn gear shift linkage. Change or lubricate shift linkage. Improperly adjusted or worn clutch. Adjust or replace the clutch. Shift forks are worn or bent. Install new shift forks. Gear shifting mechanism is defective. Defective parts must be replaced.

Transmission oil pressure is low: Lack of transmission fluid. Need to add transmission fluid. Clogged transmission fluid filter (if equipped). Service or change transmission fluid filter. Stuck relief valve. Change relief valve.

Transmission oil leakage: Seals or gaskets are worn. Gaskets or seal replacement required. Too much oil in transmission. Drain the excess oil.

Hydrostatic Transmission Troubleshooting

Hydrostatic transmission is excessively noisy: Speed control pedal linkage is damaged or out of adjustment. Repair or adjust linkage. Excessive loading. Reduce transmission load. Dirty transmission fluid or insufficient fluid level. Pour fresh fluid or add transmission fluid to proper level. Stuck relief valve. Install a new valve. Worn or defective transmission components. Replace or repair defective components.

Transmission oil overheated: Transmission overloaded. Load needs to be reduced. Clogged or damaged cooling components. Inspect all cooling components and replace or clean if necessary. Transmission fluid level is low. Need to add transmission fluid. Transmission fluid filter is clogged. Replace or service transmission fluid filter.

Power is too low: Transmission fluid level is low. Checking transmission fluid level and add if necessary. Relief valve malfunction. Change relief valve. Speed control linkage is defective or unadjusted. Adjust or install new linkage.

Transmission oil leaking: Clogged transmission fluid return pipe. Clean or change return pipe. Worn seals or gaskets. Install new seal or gaskets. High internal transmission housing pressure. Change defective parts.

Kubota B2150 Hydraulics Troubleshooting

Hydraulic system is too hot: Hydraulic fluid type is improper. The proper type of fluid must be used. Contaminated hydraulic oil. Change hydraulic oil. Air in hydraulic lines. Bleed hydraulic lines. Main relief valve is damaged. Relief valve need to be replaced.

Hydraulic oil pressure is insufficient: Insufficient hydraulic fluid. Checking hydraulic fluid level and add if necessary. Clogged hydraulic fluid filter element. Install a new hydraulic filter element. Leaks in hydraulic pipes. Identify leaks in the system and repair it. Hydraulic control valve block is set improperly. Set properly. Hydraulic pump failure. Repair or replace hydraulic oil pump. Hydraulic cylinder failure. Change or repair hydraulic cylinder.

3-point hitch won't lift or lifts slowly: Hydraulic pump malfunction. Repair or replace hydraulic oil pump. Defective main relief valve. Replace relief valve. Defective hydraulic spool valve. Repair or replace the valve. Hydraulic cylinder is broken. Change or repair hydraulic cylinder. Low hydraulic oil level. Need to add oil. Hydraulic oil filter is clogged. Change hydraulic filter element or clean if necessary. Excessive loading on the hitch. Load needs to be reduced.

Three-point hitch cannot be dropped or dropping is too slow: Hydraulic cylinder failure. Install a new hydraulic cylinder or repair it. Hydraulic control valve is set improperly. The control valve must be set correctly. Worn hitch rock shaft. Replace the shaft. The hitch is not adjusted. The hitch must be adjusted.

Jerky lifting or lowering of three-point hitch: Hydraulic oil is contaminated. Fill up with fresh hydraulic oil. Hydraulic pump is defective. Install a new hydraulic fluid pump. Air in hydraulic system. Bleed air from hydraulic system. Hydraulic control valve block is damaged. Change or repair hydraulic valve. Hydraulic cylinder is broken. Repair or change hydraulic cylinder.

Kubota B2150 Steering System Troubleshooting

Steering wheel has too much free-play: Steering column coupling or shaft has maximum wear. Replace defective part. Steering pump not working. Steering pump needs to be repaired or replaced. Steering linkage components are loose or worn. Inspect and replace as required. Steering control valve has malfunction or wear. Repair or change the control valve. Steering box components are faulty. Change defective steering gear box components.

Steering is difficult: Air lock in hydraulic steering system. Bleed air from system. Steering filter is clogged. Service steering filter. Steering fluid insufficient. Check and refill steering fluid. Steering control valve is worn or defective. Repair or change the steering control valve. Steering gear box components are damaged. Defective parts of power steering gearbox must be replaced. Faulty steering pump. Steering pump needs to be repaired or replaced. Damaged or stuck steering pump control valve. Clean or replace control valve. Improperly fitted or damaged steering column. Refit or change the steering column. Tire pressure is uneven. Adjust the tire pressure. Improper toe-in. Check and adjust toe-in.

Tractor is pulling to left or right: Steering box components are damaged. Replace defective parts of power steering box. Worn or damaged steering control valve. Check and replace as required. Incorrect toe-in. Check toe-in and correct. Steering linkage parts are loose or worn. Inspect and change as required. Front wheel bearings are worn or incorrectly adjusted. Adjust properly or change bearings. Front tyres wear unevenly. Change the tyres.

Kubota B2150 Electrical System Troubleshooting

Battery cannot be charged: Loose or corroded electrical wiring connections. Service or tighten connections. Battery terminal connectors are faulty. Terminal connectors should be replaced. Worn-out battery. Install a new battery. Defective or loose belt. Change belt or adjust belt tension.

Starter cranks slow: Low battery voltage. Battery is drained, recharge it. Battery won’t hold charge. Service charging system or change battery. Bad battery terminals or disconnected wiring. Connect wiring correctly or install new terminals.

Starter doesn't crank: Battery is discharged or defective. Charge or replace the battery. Disconnected or incorrectly connected wires. Inspect battery wires and connect correctly. Low battery output. Battery is drained, charge it. Starter motor is damaged. Change or repair starter.