________________________________________________________________________________

Kubota B2320 Troubleshooting

Kubota B2320 Diesel Engine Troubleshooting

Engine difficult to start or won't start: Fuel filter element clogging. Replace filter element. Air in the fuel lines. Bleed the fuel lines. Faulty fuel injection nozzles. Clean or replace injection nozzles. Fuel injection pump is defective. Replacement or repair required.

Engine shuts off while running: Improper setting of fuel injection pump timing. Adjust according to specifications. Dirty fuel filter. Change the filter element. Low coolant temperature. Warm up the engine.

Engine starts and immediately shuts off: Dirty fuel filter. Clean the filter element. Fuel injection pump malfunctioning. Replace or rebuild injection pump. Plugged air cleaner. Clean or change the filter.

Engine overheated: Defective radiator cap or clogged radiator fins. Clean radiator or change cap. Engine coolant is insufficient. Fill the cooling system and check components for leaks or other faults. Loose or defective fan belt. Replace as required. Insufficient engine oil. Check oil level and add oil as required.

Reduced engine power: Clogged or burnt injection nozzle. Clean or replace injection nozzles. Fuel hoses or lines are clogged. Fuel lines and hoses need to be cleaned. Air filter is dirty. Service air cleaner. Leaking cylinder head gasket. Install new cylinder head gasket.

Engine noise or knocking: Engine is cold. Warm up engine as required. Engine oil insufficient. Checking oil level and add if necessary. Incorrect adjustment of fuel injection pump timing. Adjust fuel injection pump as required. Pistons are worn or broken. Replace the pistons. Connecting rod failure or misalignment. Alignment procedure or replacement is required.

Engine stalls while idle: Too low idle RPM. Normalize low idle speed. Valve clearance is wrong. Adjust valve clearance. Fuel injection pump failure. Rebuild or replace pump.

Oil pressure is insufficient: Insufficient engine oil. Check and refill the oil. Oil pump is defective. Remove and inspect oil pump. Oil filter element clogged. Clean or replace engine oil filter element.

Kubota B2320 Transmission Troubleshooting

Transmission noises: Gears are defective or backlash is improper. Replace defective gears or set backlash properly. Worn or bent gear shift forks. Install new shift forks. Worn or stuck shaft splines. Shaft need to be replaced. Lack of transmission oil supply. Fill the transmission housing with oil. Worn or cracked bearings. Faulty bearings should be changed. Transmission fluid is dirty. Fill up with fresh transmission fluid.

Hard shifts: Gear shift linkage is rusty or worn. Install new shift linkage. Improperly adjusted or worn clutch. Adjust or change the clutch. Worn or bent gear shift forks. Replace defective shift forks. Gearshift mechanism malfunction. Identify and replace failed parts.

Transmission fluid pressure is insufficient: Low oil level. Need to add transmission oil. Transmission oil filter is clogged (if fitted). Clean or change transmission oil filter. Relief valve is stuck. Install a new valve.

External fluid leaks: Damaged seals or gaskets. Install new components. Too much fluid in transmission. Excess fluid must be drained.

Hydrostatic Transmission Troubleshooting

HST transmission is excessively noisy: Worn or unadjusted speed control linkage. Adjust or repair linkage. Transmission overloaded. Reduce transmission load. Dirty transmission fluid or insufficient fluid level. Fill to required level or change the fluid. Stuck relief valve. Change the valve. Worn or defective transmission components. After disassembly and inspection, replace defective components.

Transmission fluid overheats: Excessive loading. Reduce the load is required. Cooling components are clogged or damaged. Check all cooling components and change or repair if required. Transmission fluid level is low. Add fluid to the transmission housing. Transmission fluid filter is clogged. Service or replace the transmission fluid filter.

Power is too low: Low oil level. Need to add transmission oil. Relief valve is stuck. Replace valve as required. Bent or unadjusted speed control pedal linkage. Repair or adjust linkage.

Transmission oil leakage: Plugged oil return tube. Clean or replace return tube. Worn seals or gaskets. Install new seal or gaskets. High internal transmission case pressure. Change defective parts.

Kubota B2320 Hydraulics Troubleshooting

Hydraulic system is too hot: Improper type of hydraulic fluid. The correct type of fluid must be used. Hydraulic oil contamination. Change the oil. There is air in the hydraulic system. Bleed hydraulic system. Main relief valve malfunctioning. Replace relief valve.

Hydraulic fluid pressure too low: Low hydraulic oil level. Checking hydraulic oil level and add if necessary. Dirty hydraulic fluid filter. Clean or replace the hydraulic filter. Hydraulic piping is leaking. Identify leaks in the system and repair it. Not adjusted hydraulic spool valve. Need to adjust spool valve. Hydraulic pump malfunction. Change or repair hydraulic oil pump. Hydraulic cylinder is defective. Replace or repair hydraulic cylinder.

Hitch won't raise or raises slowly: Faulty hydraulic pump. Change or repair hydraulic fluid pump. Main relief valve is damaged. Install a new relief valve. Hydraulic control valve block is faulty. Repair or replace hydraulic valve. Faulty hydraulic cylinder. Install a new hydraulic cylinder or repair it. Insufficient hydraulic fluid. Fill the system to proper hydraulic fluid level. Clogged hydraulic oil filter. Clean or replace the hydraulic filter. Excessive hitch loading. Reduce hitch load.

Hitch cannot be lowered or lowering is too slowly: Faulty hydraulic cylinder. Change or repair hydraulic cylinder. Hydraulic control valve block is set improperly. Set properly. Worn hitch cross shaft. Replace the shaft. Three-point hitch is out of adjustment. Adjust the hitch.

Hitch drop or lift is jerky: Contaminated hydraulic oil. Change hydraulic oil. Hydraulic pump is faulty. Repair or replace hydraulic oil pump. Air trapped in hydraulic system. Bleed air from system. Hydraulic control valve block is damaged. Install a new valve or repair it. Hydraulic cylinder is faulty. Install a new hydraulic cylinder or repair it.

Kubota B2320 Steering System Troubleshooting

Excessive steering wheel play: Steering column shaft or coupling is worn out. Change faulty part. Hydraulic steering pump is defective. Repair or replace steering pump. Steering linkage parts are loose or worn. Repair or replace steering linkage. Worn or defective hydrostatic steering unit. Change or repair steering unit if required.

Difficult steering: Air trapped inside steering system. Air-bleed steering system. Steering filter is clogged. Replace steering filter element. Lack of steering fluid. Need to add steering oil. Hydrostatic steering unit is worn or defective. Replace or repair steering unit as required. Steering pump malfunction. Steering pump needs to be repaired or replaced. Pump flow control valve is damaged or stuck. Replace or clean flow control valve. Improperly mounted or worn steering column. Mount the steering column as required or change it. Front tyres are worn unevenly. Install new tyres. Improper toe-in. Check and adjust toe-in. Steering cylinder leakage. Change damaged piston rod or worn piston seals.

Front wheels wander to left or right: Hydrostatic steering unit is damaged or worn. Check and replace as required. Damaged steering cylinder. Replace or repair steering cylinder. Incorrect toe-in. Check toe-in and correct. Loose or worn steering linkage components. Check and replace as required. Worn or incorrectly adjusted or worn front wheel bearings. Adjust correctly or install new bearings. Front tires wear unevenly. Change the tires.

Kubota B2320 Electrical Troubleshooting

Battery does not charge: Wiring connections are corroded or loose. Tighten or clean electrical wiring connections. Electrical terminal connectors are defective. Change terminal connectors. Worn-out battery. Battery replacement required. Damaged or loose belt. Install a new belt or adjust belt tension.

Starter cranks slow: Battery voltage is low. Battery is drained, recharge it. Battery discharges quickly. Service charging system or change battery. Disconnected wires or corroded battery terminals. Connect cables correctly or replace terminals.

Starter is not working: Battery is low or faulty. Battery needs to be recharged or replaced. Wiring is improperly connected or disconnected. Check wiring and connect properly. Battery voltage is low. Recharge the battery. Damaged starter motor. Replace or repair starter.