________________________________________________________________________________

Kubota BX2380 Troubleshooting

Kubota BX2380 Diesel Engine Troubleshooting

Engine starts hard or will not start: Clogged fuel filter. Service or replace the filter. Air trapped in fuel system. Bleed air. Fuel injection nozzles are clogged or faulty. Check and replace nozzles if required. Fuel injection pump malfunction. Replace injection pump or repair it.

Engine shuts off suddenly while running: Improper fuel injection timing. Check the fuel injection pump timing adjustment. Fuel filter plugged. Clean the filter element. Low coolant temperature. Warm up the engine.

Engine starts but stalls immediately: Fuel filter element clogging. Replace the filter element. Fuel injection pump is not operating properly. Change or repair the pump. Air cleaner is dirty. Replace air filter element.

Engine overheating: Faulty radiator cap or dirty radiator fins. Clean radiator or replace cap. Lack of engine coolant. Fill the cooling system and check components for leaks or other faults. Loose or damaged fan belt. Fan belt must be replaced. Engine oil level low. Check and refill engine oil.

Poor engine power: Clogged or burnt injection nozzle. Test injection nozzles and change if necessary. Dirt in the fuel hoses or lines. Service fuel hoses and lines. Restricted intake air. Carry out maintenance on air filter. Cylinder-head gasket is broken. Replace cylinder head gasket.

Abnormal engine noise or knocking: Engine is not fully warmed up. Warm up engine as required. Insufficient engine oil. Add oil to the engine crankcase. Improper fuel injection timing. Set the fuel pump timing correctly. Worn or broken pistons. Pistons need to be replaced. Connecting rod is worn or misaligned. Need to align or replace the connecting rod.

Engine stalls at low idle speed: Improperly adjusted low idle speed. Adjust the low idle speed. The valve clearance is not adjusted. Have it adjusted. Damaged fuel injection pump. Install a new fuel pump or repair.

Low oil pressure: Not enough oil in the engine. Add oil as required. Oil pump is worn or damaged. Repair or replace. Engine oil filter is plugged. Clean or change engine oil filter.

Kubota BX2380 Hydrostatic Transmission Troubleshooting

Hydrostatic transmission makes excessive noise: Worn or unadjusted speed control linkage. Adjust or install new linkage. Excessive transmission load. Reduce loading. Dirty transmission fluid or insufficient fluid level. Top up to proper level or change transmission fluid. Relief valve is damaged. Install a new valve. Damaged or worn components of hydrostatic transmission. Check hydrostatic transmission components for defect or damage and change if necessary.

Transmission oil overheats: Excessive loading. The load should be reduced. Clogged or damaged cooling components. Inspect all cooling components and replace or repair if necessary. Transmission fluid level is low. Check and refill the transmission fluid. Dirty transmission fluid filter. Replace or service transmission fluid filter.

Loss of power: Insufficient transmission oil. Check transmission oil level and add oil as required. Relief valve is damaged. Install a new valve. Speed control pedal linkage is bent or not adjusted. Adjust or install new linkage.

Transmission oil leakage: Plugged transmission fluid return tube. Service or replace return tube. Seals or gaskets are broken. Install new gaskets or seal. High internal transmission housing pressure. Replace worn components.

Kubota BX2380 Hydraulic System Troubleshooting

Hydraulic system overheating: Improper hydraulic oil type. The proper type of hydraulic oil must be used. Dirty hydraulic oil. The oil must be changed. Air in hydraulic system. Bleed air from hydraulic system. Defective main relief valve. Replace relief valve.

Insufficient hydraulic oil pressure: Low hydraulic fluid level. Add fluid as required. Clogged hydraulic fluid filter. Hydraulic filter maintenance required. Leaking hydraulic pipes. Identify leaks in the system and repair it. Incorrect setting hydraulic spool valve. Use the correct setting. Hydraulic pump failure. Replace or repair hydraulic oil pump. Defective hydraulic cylinder. Install a new hydraulic cylinder or repair it.

3-point hitch cannot be raised or raising is too slowly: Faulty hydraulic pump. Replace or repair hydraulic fluid pump. Main relief valve is damaged. Relief valve replacement required. Hydraulic spool valve block is defective. Repair or change the valve. Hydraulic cylinder not working. Repair or install a new hydraulic cylinder. Insufficient hydraulic fluid. Fill the system to proper hydraulic fluid level. Clogged hydraulic oil filter. Clean or replace the hydraulic filter. Excessive loading on the hitch. Reduce the load is required.

3-point hitch won't lower or lowers slowly: Hydraulic cylinder is broken. Change or repair hydraulic cylinder. Incorrect setting hydraulic spool valve. Use the correct setting. Damaged hitch rock shaft. Install a new shaft. Hitch is out of adjustment. Adjustment is required.

Hitch jerks when drop or lift: Contaminated hydraulic fluid. Change hydraulic fluid. Hydraulic pump malfunction. Change or repair hydraulic fluid pump. Air in hydraulic pipes. Bleed hydraulic pipes. Defective hydraulic spool valve block. Repair or change the valve. Hydraulic cylinder is defective. Install a new hydraulic cylinder or repair it.

Kubota BX2380 Steering System Troubleshooting

Steering wheel free play is excessive: Steering column coupling or shaft has maximum wear. Change defective component. Defective hydraulic steering pump. Install a new hydraulic steering pump. Steering linkage joints are worn or loose. Change or repair steering linkage. Hydrostatic steering unit has malfunction or wear. Change or repair steering unit if required.

Steering wheel is difficult to turn: Air in steering system. Bleed the steering system. Clogged steering filter. Install new steering filter element. Lack of steering oil. Fill the steering system with oil. Hydrostatic steering unit is damaged or worn. Repair or change the steering unit. Steering pump malfunction. Steering pump needs to be replaced or repaired. Damaged or stuck steering pump control valve. Service or replace flow control valve. Defective or incorrectly mounted steering column. Change steering column or mount correctly. Front tires are worn unevenly. Install new tires. Incorrect toe-in. Check toe-in and correct. Steering cylinder leaks. Damaged cylinder seals or worn piston rod.

Tractor pulls to right or left: Hydrostatic steering unit is worn or defective. Repair or replace the steering unit. Steering cylinder is damaged. Repair or change hydraulic steering cylinder. Incorrect toe-in. Check and adjust toe-in. Steering linkage joints are worn or loose. Check and change as required. Improperly adjusted or worn front wheel bearings. Replace or adjust the bearings correctly. Tire pressure uneven. Inflate the tires correctly.

Kubota BX2380 Electrical System Troubleshooting

Battery won’t charge: Loose or corroded electrical wiring connections. Tighten or clean connections. Faulty battery terminal connectors. Terminal connectors need to be changed. Worn-out battery. Battery replacement required. Damaged or loose belt. Adjust belt tension or install a new belt.

Starter motor turns slow: Battery capacity is low. Charge the battery. Battery does not hold charge. Service battery or replace it. Bad terminals or disconnected battery cables. Check wiring and clean or replace terminals.

Starter motor won't turn: Battery is low or faulty. Battery needs to be recharged or replaced. Battery wires are disconnected or incorrectly connected. Check wires and connect correctly. Battery power is low. Recharge the battery. Starter motor is damaged. Starter needs to be changed.