________________________________________________________________________________

Kubota LX2610 Troubleshooting

Kubota LX2610 Engine Troubleshooting

Engine hard to start or will not start: Fuel filter plugged. Service the filter. Air in fuel system. Bleed fuel system. Fuel injection nozzles are dirty or defective. Service or change injection nozzles. Fuel injection pump is broken. Change or repair the pump.

Engine stalls while running: Wrong setting of fuel injection pump timing. Set up as recommended. Clogged fuel filter. Clean or replace the filter. Engine is not preheated. Warm up to required temperature.

Diesel starts but stalls immediately: Fuel filter element is dirty. Service the filter. Fuel injection pump is defective. Replace or repair injection pump. Air filter is dirty. Service air cleaner.

Engine overheated: Clogged radiator fins or leaking radiator cap. Install new cap or clean radiator. Not enough coolant. Fill the cooling system and check components for leaks or other faults. Loose or defective fan belt. Change the fan belt. Low engine oil level. Check oil level and add oil as required.

Poor engine power: Clogged or defective injection nozzles. Service or change injection nozzles. Fuel lines or hoses are dirty. Clean fuel system hoses and lines. Clogged air filter element. Install new air filter element. Cylinder head gasket is damaged. Replace the gasket as required.

Abnormal engine knocking or noise: Low coolant temperature. Warm up engine as required. Insufficient engine oil. Fill up the engine oil. Improper fuel injection timing. Adjust as recommended. Pistons are broken or worn. Replace the pistons. Misaligned or defective connecting rod. Need to align or replace the connecting rod.

Engine stalls at idle: Too low idle RPM. Adjust low idle speed. Valve out of adjustment. Adjust to proper valve clearance. Defective fuel injection pump. Repair or replace injection pump.

Oil pressure is low: Engine oil level low. Add oil to the engine crankcase. Oil pump malfunction. Check and replace if necessary. Engine oil filter is plugged. Service or replace engine oil filter.

Kubota LX2610 Hydrostatic Transmission Troubleshooting

Hydrostatic transmission is making noise: Speed control linkage is worn or unadjusted. Replace or adjust linkage. Excessive transmission load. Load needs to be reduced. Oil is dirty or oil level is too low. Add oil to the correct level or fill the transmission with fresh oil. Relief valve malfunction. Change the valve. Damaged or worn components of hydrostatic transmission. Check hydrostatic transmission components for defect or damage and change if necessary.

Transmission fluid overheating: Excessive loading. Reduce transmission load. Defective or plugged cooling components. Check all cooling components and clean or replace if required. Transmission oil level is low. Fill the transmission housing with oil. Transmission oil filter is dirty. Clean or change transmission oil filter.

Loss of power: Lack of transmission fluid. Check and refill the transmission fluid. Relief valve is damaged. Replace valve as required. Speed control linkage is defective or unadjusted. Change or adjust linkage.

Transmission fluid leaking: Plugged oil return tube. Clean or replace return tube. Seals or gaskets are broken. Gaskets or seal need to be replaced. Internal transmission housing pressure is too high. Check transmission parts for damage or wear and replace if required.

Kubota LX2610 Hydraulics Troubleshooting

Hydraulic system is too hot: Wrong hydraulic fluid type. Pour the proper type of fluid. Hydraulic oil is dirty. Hydraulic oil change required. Air in the hydraulic system. Air bleeding. Main relief valve is damaged. Change relief valve.

Insufficient hydraulic fluid pressure: Insufficient hydraulic fluid. Checking hydraulic fluid level and add if necessary. Dirty hydraulic fluid filter element. Clean the hydraulic filter or install new filter element. Hydraulic piping is leaking. Find leaks in the system and fix it. Not adjusted hydraulic control valve. Need to adjust. Hydraulic pump not working. Change or repair hydraulic fluid pump. Hydraulic cylinder malfunction. Repair or replace hydraulic cylinder.

3-point hitch can't lift or lifts too slowly: Hydraulic pump is defective. Repair or replace hydraulic oil pump. Defective main relief valve. Relief valve replacement required. Hydraulic control valve block is faulty. Repair or change the valve. Hydraulic cylinder failure. Replace or repair hydraulic cylinder. Low hydraulic oil level. Check and refill the hydraulic oil. Clogged hydraulic fluid filter. Install a new hydraulic filter element. Excessive load on hitch. Reduce loading.

3-point hitch won't lower or lowers slowly: Defective hydraulic cylinder. Install a new hydraulic cylinder or repair it. Incorrect adjusted hydraulic control valve. Adjust correctly. Hitch rock shaft is damaged. Replace the shaft. 3-point hitch is out of adjustment. Adjust the 3-point hitch.

Jerky lowering or lifting of the hitch: Hydraulic fluid is dirty. Hydraulic fluid change required. Hydraulic pump malfunction. Repair or replace hydraulic oil pump. Air in the hydraulic system. Air bleeding. Damaged hydraulic control valve. Repair or change hydraulic valve. Broken hydraulic cylinder. Install a new hydraulic cylinder or repair it.

Kubota LX2610 Steering System Troubleshooting

Excessive free play of steering wheel: Steering column shaft or coupling is worn out. Change faulty component. Faulty steering pump. Install a new steering pump. Worn or loose steering linkage joints. Inspect and replace as required. Worn or damaged power steering control valve. Repair or replace the steering control valve.

Steering wheel turns hard: Air lock in the steering system. Bleed the steering system. Steering filter element is clogged. Clean steering filter element. Steering fluid level low. Checking steering fluid level and add it if necessary. Power steering control valve has wear or malfunction. Inspect and change as required. Faulty steering pump. Repair or replace steering pump. Stuck or worn pump flow control valve. Replace or service control valve. Improperly mounted or worn steering column. Mount the steering column as required or change it. Front tyres are worn unevenly. Install new tyres. Incorrect toe-in. Check and adjust toe-in. Steering cylinder leaks. Replace scratched piston rod or worn cylinder seals.

Tractor pulls to left or right: Power steering control valve has wear or malfunction. Repair or replace the steering control valve. Steering cylinder is worn. Replace or repair hydraulic steering cylinder. Incorrect toe-in. Check toe-in and correct. Steering linkage parts are loose or worn. Replace or repair steering linkage. Front wheel bearings are defective or improperly adjusted. Replace the bearings or adjust it properly. Front tyres are worn unevenly. Install new tyres.

Kubota LX2610 Electrical Troubleshooting

Battery will not charge: Electrical wire connections are corroded or loose. Service or tighten connections. Battery terminal clamps are faulty. Terminal clamps need to be replaced. Battery failing. Replace the battery. Belt is damaged or loose. Replace belt or adjust belt tension.

Starter turns slowly: Low battery voltage. Charge the battery. Battery is not holding charge. Service battery or replace it. Disconnected wiring or bad battery terminals. Check cables and clean or change terminals.

Starter will not crank: Battery is discharged or defective. Charge or change the battery. Disconnected or incorrectly connected wires. Inspect battery wires and connect correctly. Low battery capacity. Charge the battery. Starter motor is defective. Change or repair starter.