________________________________________________________________________________

Kubota M105X Troubleshooting

Kubota M105X Engine Troubleshooting

Engine starts up hard or won't start: Fuel filter plugged. Service the filter. Air in the fuel lines. Bleed the fuel lines. Clogged injection nozzle. Clean or change injection nozzles. Fuel injection pump is not operating properly. Rebuild or replace pump.

Engine stops suddenly during operation: Improper setting of fuel injection pump timing. Set it up as required. Clogged fuel filter. Replace the filter element. Engine is cold. Warm up to required temperature.

Diesel starts and then shuts off: Fuel filter element clogging. Clean the filter element. Defective fuel injection pump. Repair or install a new fuel pump. Plugged air cleaner. Clean or change.

Engine overheats: Radiator core is clogged or radiator cap is leaking. Install new cap or clean radiator. Engine coolant is insufficient. Add coolant fluid and inspect the cooling system for leaks. Damaged or worn fan belt. Replace the fan belt. Insufficient engine oil. Fill up the oil to required level.

Poor engine power: Fuel injection nozzles fault. Clean or change injection nozzles. Fuel lines or hoses are clogged. Clean fuel lines and hoses. Air filter element clogged. Clean or replace the element. Cylinder head gasket is worn. Install a new gasket.

Engine knocking or noise: Engine has not warmed up to the recommended temperature. Engine is not warmed up to the required temperature. Lack of engine oil. Fill up the oil to required level. Fuel injection pump timing is not adjusted. Check the fuel injection pump timing adjustment. Worn or scored pistons. Replace the pistons as required. Connecting rod failure or misalignment. Need to change or align the connecting rod.

Engine stops while idle: Incorrectly set low idle speed. Correct low idle adjustment. The valve clearance is incorrect. Check and adjust. Fuel injection pump is not working correctly. Replace injection pump or repair it.

Oil pressure is low: Oil level is low. Fill up the engine oil. Worn oil pump. Inspect and change as required. Oil filter element clogged. Service or change engine oil filter element.

Kubota M105X Transmission Troubleshooting

Transmission makes noise: Gears are damaged or backlash is incorrect. Change worn gears or adjust backlash correctly. Worn or bent gear shift forks. Shift forks need to be changed. Shaft splines are worn or damaged. Replace defective shaft. Transmission fluid level is low. Checking transmission fluid level and add if necessary. Worn or cracked bearings. Bearings need to be replaced. Transmission fluid is contaminated. Fill up with fresh transmission fluid.

Hard to shift gears: Corroded or worn gear shift linkage. Install a new gear shift linkage. Malfunction or incorrect clutch adjustment. Change or adjust clutch. Worn or damaged gear shift forks. Change defective shift forks. Worn out parts of the gearshift mechanism. Replace worn parts.

Transmission oil pressure is insufficient: Transmission oil level is low. Check transmission oil level and add oil as required. Clogged transmission oil filter element (if fitted). Clean or replace the transmission filter. Stuck relief valve. Replace valve as required.

Transmission fluid leakage: Damaged gaskets or seals. Install new gaskets or seal. Transmission oil level is high. Correct the oil volume.

Kubota M105X Hydraulics Troubleshooting

Hydraulic system overheated: Wrong type of hydraulic oil. Pour the correct type of hydraulic oil. Dirty hydraulic oil. The oil must be changed. Air in the hydraulic system. Air bleeding. Main relief valve is faulty. Relief valve replacement required.

Hydraulic oil pressure is insufficient: Insufficient hydraulic oil. Check and refill the hydraulic oil. Clogged hydraulic fluid filter. Hydraulic filter maintenance required. Hydraulic piping is leaking. Inspect hydraulic system for leaks and repair it. Incorrect setting hydraulic control valve block. Set correctly. Hydraulic pump is faulty. Repair or replace hydraulic oil pump. Hydraulic cylinder is defective. Replace or repair hydraulic cylinder.

3-point hitch cannot be raised or raising is too slowly: Hydraulic pump not working. Change or repair hydraulic fluid pump. Faulty main relief valve. Relief valve replacement required. Defective hydraulic spool valve. Repair or replace the valve. Defective hydraulic cylinder. Install a new hydraulic cylinder or repair it. Hydraulic fluid is insufficient. Fill the system to proper hydraulic fluid level. Hydraulic oil filter is clogged. Service or replace the hydraulic filter. Excessive loading on the hitch. The load should be reduced.

3-point hitch does not lower or lowers very slowly: Hydraulic cylinder is faulty. Repair or change hydraulic cylinder. Hydraulic control valve block is set improperly. Set properly. Damaged hitch rock shaft. Replace the shaft. The hitch has not been adjusted. Adjust three-point hitch as required.

Jerky lifting or lowering of three-point hitch: Hydraulic fluid is contaminated. Fill up with new hydraulic fluid. Hydraulic pump is faulty. Install a new hydraulic fluid pump. Air in the hydraulic system. Air bleeding. Hydraulic control valve block is damaged. Repair or change hydraulic valve. Hydraulic cylinder failure. Repair or replace hydraulic cylinder.

Kubota M105X Steering Troubleshooting

Steering wheel free play is excessive: Steering column shaft or coupling has maximum wear. Change faulty component. Steering pump not working. Steering pump needs to be repaired or replaced. Loose or worn steering linkage parts. Check and replace as required. Hydrostatic steering unit has wear or damage. Repair or replace the steering unit.

Steering wheel is very heavy to turn: Air in the hydraulic steering system. Bleed the steering system. Clogged steering filter element. Clean or replace the element. Not enough steering fluid. Fill up steering fluid to required level. Hydrostatic steering unit is worn or defective. Inspect and change as required. Steering pump not working. Install a new hydraulic steering pump. Stuck or faulty steering pump control valve. Clean or install new control valve. Defective or incorrectly mounted steering column. Change steering column or mount correctly. Tyre pressure is uneven. Adjust the tyre pressure. Improper toe-in. Adjust toe-in properly. Leaking steering cylinder. Damaged cylinder seals or worn piston rod.

Tractor pulls to right or left: Hydrostatic steering unit has wear or malfunction. Inspect and change as required. Steering cylinder malfunction. Replace or repair steering cylinder. Incorrect toe-in. Check and adjust toe-in. Worn or loose steering linkage assembly. Repair or change steering linkage. Worn or incorrectly adjusted or worn front wheel bearings. Adjust correctly or replace bearings. Uneven tire pressure. Inflate the tires properly.

Kubota M105X Electrical Troubleshooting

Battery won’t charge: Electrical cable connections are corroded or loose. Tighten or service cable connections. Battery terminal clamps are faulty. Terminal clamps should be changed. Dead cell in battery. Install a new battery. Belt is defective or loose. Adjust belt tension or replace belt.

Starter motor turns slow: Low battery output voltage. Battery is drained, charge it. Battery does not hold charge. Service or replace the battery. Terminals are faulty or battery cables are disconnected. Check cables and service or change terminals.

Starter does not work: Battery is drained or worn. Charge or change the battery. Disconnected or improperly connected wiring harness. Inspect battery wiring harness and connect as required. Low battery output voltage. Recharge the battery. Damaged starter motor. Change or repair starter.