________________________________________________________________________________

Kubota MX5000 Troubleshooting

Kubota MX5000 Engine Troubleshooting

Engine starts hard or won't start: Fuel filter element is dirty. Service or replace the filter. There is air in the fuel system. Bleed the system. Dirty or damaged injection nozzles. Change fuel injection nozzles. Fuel injection pump failure. Replace injection pump or repair it.

Engine stalls while running: Improper setting of fuel injection pump timing. Adjust fuel injection pump as required. Clogged fuel filter. Service the filter. Engine not warmed up. Engine is not warmed up to the required temperature.

Engine starts but stalls immediately: Fuel filter plugged. Replace filter element. Fuel injection pump malfunctioning. Install a new pump or rebuild. Clogged air filter element. Service air cleaner.

Engine overheating: Radiator core is clogged or radiator cap is leaking. Change cap or clean radiator. Coolant level is low. Add coolant and check the components of cooling system. Damaged or worn fan belt. Replace the fan belt. Not enough engine oil. Fill the crankcase with engine oil.

Engine lacks power: Fuel injection nozzles are damaged. If necessary, replace with a new nozzle. Fuel hoses or lines are clogged. Service fuel hoses and lines. Air filter is dirty. Clean air cleaner element. Leaking cylinder head gasket. Replace the gasket as required.

Engine noises or knocks: Coolant temperature is low. Warm up to required temperature. Engine oil level low. Checking oil level and add if necessary. Improper setting of fuel injection pump timing. Adjust the pump as required. Broken or worn pistons. Pistons replacement required. Connecting rod misalignment or failure. Connecting rod needs to be replaced or aligned.

Engine stops while idle: Low idle speed setting is not correct. Test and adjust. Valve clearance is not correct. Need to adjust valve clearance. Defective fuel injection pump. Rebuild or install a new injection pump.

Oil pressure is insufficient: Low crankcase oil level. Add oil to the engine crankcase. Oil pump is damaged. Check and replace if necessary. Oil filter element clogging. Service or change engine oil filter element.

Kubota MX5000 Transmission Troubleshooting

Transmission noise: Defective gears or improper backlash. Replace gears or adjust backlash correctly. Damaged or worn gear shift forks. Shift forks need to be replaced. Damaged or worn shaft splines. Shaft need to be changed. Transmission fluid level is low. Need to add transmission fluid. Bearings are broken or worn. Replace faulty bearings. Transmission fluid is dirty. Transmission fluid change required.

Gears are hard to shift: Gear shift linkage is corroded or worn. Replace or lubricate the shift linkage. Worn or improperly adjusted clutch. Adjust clutch or change if necessary. Shift forks are bent or worn out. Replace the shift forks. Worn out parts of the gearshift mechanism. Replace worn parts.

Transmission oil pressure is low: Transmission oil insufficient. Check and refill the transmission oil. Transmission fluid filter element clogging (if equipped). Service or replace the transmission fluid filter. Relief valve malfunction. Replace valve as required.

Transmission oil leaking: Seals or gaskets are worn. Install new seal or gaskets. Too much fluid in transmission. Excess fluid must be drained.

Kubota MX5000 Hydraulics Troubleshooting

Hydraulic system overheating: Hydraulic oil type is incorrect. Pour the correct type of oil. Hydraulic oil is dirty. Hydraulic oil change required. Air in hydraulic system. Bleed air from hydraulic system. Faulty main relief valve. Install a new relief valve.

Low hydraulic system pressure: Insufficient hydraulic fluid. Fill up the hydraulic fluid. Hydraulic fluid filter element is clogged. Clean or replace the hydraulic filter. Leaks in hydraulic lines. Check the hydraulic system and fix leaks. Incorrect adjusted hydraulic spool valve. Adjust the spool valve correctly. Hydraulic pump failure. Repair or replace hydraulic oil pump. Hydraulic cylinder is faulty. Install a new hydraulic cylinder or repair it.

3-point hitch cannot be raised or raising is too slowly: Hydraulic pump malfunction. Install a new hydraulic oil pump. Main relief valve failure. Change relief valve. Hydraulic spool valve is faulty. Repair or replace the valve. Broken hydraulic cylinder. Change or repair hydraulic cylinder. Insufficient hydraulic fluid. Add fluid as required. Clogged hydraulic oil filter. Clean the hydraulic filter element or replace if necessary. Excessive load on hitch. The load should be reduced.

Hitch fails to drop or drops slowly: Defective hydraulic cylinder. Change or repair hydraulic cylinder. Incorrect adjusted hydraulic control valve. Adjust correctly. Damaged lift arm shaft. Replace the shaft. Unadjusted hitch. Adjust 3-point hitch as required.

Hitch lift or drop is not smoothly: Hydraulic oil contamination. Change the oil. Faulty hydraulic pump. Repair or replace hydraulic oil pump. Air in hydraulic lines. Bleed hydraulic lines. Defective hydraulic spool valve block. Repair or change hydraulic valve. Hydraulic cylinder not working. Repair or change hydraulic cylinder.

Kubota MX5000 Steering System Troubleshooting

Excessive play in steering: Worn steering column shaft or coupling. Change faulty part. Steering pump is faulty. Install a new steering pump. Loose or worn steering linkage components. Check and change as required. Hydrostatic steering unit is worn or defective. Check and replace as required.

Steering is stiff: Air in steering system. Bleed the steering system. Dirty steering filter. Change steering filter element. Not enough steering fluid. Fill up steering fluid to required level. Worn or defective hydrostatic steering unit. Inspect and change as required. Defective hydraulic steering pump. Repair or replace steering pump. Steering pump control valve is stuck or faulty. Replace or clean flow control valve. Incorrectly fitted or worn steering column. Refit or replace the steering column. Front tyres are worn unevenly. Install new tyres. Incorrect toe-in. Adjust toe-in wheels. Steering cylinder is leaking. Change worn piston rod or damaged cylinder seals.

Front wheels wander to right or left: Hydrostatic steering unit has malfunction or wear. Inspect and replace as required. Damaged steering cylinder. Repair or replace steering cylinder. Not adjusted toe-in. Adjust toe-in properly. Worn or loose steering linkage assembly. Change or repair steering linkage. Improperly adjusted or defective front hub bearings. Adjust correctly or install new bearings. Tire pressure is uneven. Adjust the tire pressure.

Kubota MX5000 Electrical Troubleshooting

Battery is not charging: Wiring connections are loose or corroded. Tighten or service cable connections. Battery terminal clamps are defective. Install new terminal clamps. Battery is worn. Install a new battery. Loose or defective belt. Adjust belt tension or install a new belt.

Starter motor turns slow: Low battery capacity. Low battery charging, charge as required. Battery does not hold charge. Service charging system or change battery. Disconnected battery cables or bad terminals. Check wiring and clean or replace terminals.

Starter will not work: Battery is discharged or defective. Charge or replace the battery. Wiring is incorrectly connected or disconnected. Inspect wiring and connect correctly. Low battery capacity. Recharge the battery. Starter motor is defective. Repair or change starter.