________________________________________________________________________________

Massey Ferguson 1533 Troubleshooting

Massey Ferguson 1533 Engine Troubleshooting

Diesel hard to start or doesn't start: Fuel filter element is clogged. Service the filter. Air in the fuel pipes. Bleed the fuel pipes. Clogged or burnt injection nozzle. Change fuel injection nozzles. Fuel injection pump is faulty. Change pump or rebuild it.

Engine stops unexpectedly during operation: Fuel injection pump timing is not adjusted. Use the correct fuel injection pump timing adjustment. Clogged fuel filter. Install new filter element. Engine is not preheated. Warm up to required temperature.

Diesel starts and stalls immediately: Clogged fuel filter. Clean the filter element. Fuel injection pump malfunction. Repair or change injection pump. Dirty air filter. Clean or replace the element.

Engine overheats: Radiator fins are clogged or radiator cap is faulty. Clean radiator or replace cap. Low coolant level. Add coolant and check the components of cooling system. Fan belt is worn or faulty. Belt replacement is recommended. Engine oil level is insufficient. Fill the crankcase with engine oil.

Engine power is reduced: Fuel injection nozzles are faulty or clogged. Inspect nozzles and replace if necessary. Restricted fuel hoses or lines. Clean fuel lines and hoses. Clogged air filter. Clean or replace element. Cylinder head gasket defective. Cylinder-head gasket replacement required.

Abnormal engine knocking or noise: Engine is not preheated. Engine is not warmed up to the required temperature. Engine oil level low. Checking oil level and add if necessary. Fuel injection pump timing is not adjusted. Adjust according to specifications. Worn or scored pistons. Install new pistons. Connecting rod is worn or misaligned. Align or change connecting rod.

Engine stalls at low idle speed: Low idle speed setting is not correct. Correct low idle adjustment. Valve out of adjustment. Adjust valve clearance. Fuel injection pump is not operating properly. Replace injection pump or repair it.

Low oil pressure: Insufficient engine oil. Need to add oil. Oil pump is defective. Install a new pump. Plugged engine oil filter. Service or change engine oil filter element.

Massey Ferguson 1533 Transmission Troubleshooting

Transmission makes excessive noise: Damaged gears or incorrect backlash. Adjust backlash properly or replace the gears. Worn or bent gear shift forks. Replace defective shift forks. Shaft splines are stuck or worn out. Replace defective shaft. Low oil level. Fill the transmission housing to proper oil level. Bearings are damaged or worn. Faulty bearings should be changed. Transmission fluid contamination. Fill up with fresh transmission fluid.

Hard shifts: Worn or rusty gear shift linkage. Change or lubricate shift linkage. Worn or unadjusted clutch. Adjust or change the clutch. Worn or bent gear shift forks. Replace defective shift forks. Gearshift mechanism malfunction. Identify and replace failed parts.

Transmission oil pressure is insufficient: Lack of transmission oil supply. Need to add transmission oil. Clogged transmission oil filter element (if fitted). Service or replace the transmission oil filter. Relief valve failure. Replace relief valve as required.

Transmission oil leaking: Damaged gaskets or seals. Gaskets or seal need to be replaced. Transmission oil level is high. Correct the oil volume.

Hydrostatic Transmission Troubleshooting

HST transmission makes excessive noise: Defective or not adjusted speed control pedal linkage. Replace or adjust linkage. Transmission is under excessive load. Reduce loading. Contaminated transmission fluid or low fluid level. Fill to required level or change the fluid. Relief valve failure. Change relief valve. Transmission parts are worm or defective. Check internal transmission parts for damage or wear and replace if required.

Transmission oil overheats: Transmission overload. Reduce transmission load. Cooling components are plugged or defective. Inspect all cooling components and service or change if necessary. Lack of transmission oil supply. Fill the transmission housing with oil. Dirty transmission fluid filter. Replace or service transmission fluid filter.

Loss of power: Transmission fluid insufficient. Fill the transmission housing to proper fluid level. Relief valve failure. Replace the valve. Defective or not adjusted speed control pedal linkage. Change or adjust linkage.

Transmission fluid leaks: Oil drain line is clogged. Clean or change the line. Damaged seals or gaskets. Seals and gaskets need to be replaced. Transmission case internal pressure is too high. Repair or replace damaged components.

Massey Ferguson 1533 Hydraulics Troubleshooting

Excessive hydraulic system heat: Improper type of hydraulic fluid. The correct type of fluid must be used. Dirty hydraulic fluid. The fluid must be changed. Air in the hydraulic system. Air bleeding. Damaged main relief valve. Change relief valve.

Insufficient hydraulic fluid pressure: Hydraulic oil level low. Need to add oil. Hydraulic oil filter is clogged. Replace filter element or clean if required. Leaks in hydraulic pipes. Check the hydraulic system and fix leaks. Incorrect adjusted hydraulic spool valve. Adjust the spool valve correctly. Hydraulic pump is faulty. Change or repair hydraulic oil pump. Hydraulic cylinder not working. Replace or repair hydraulic cylinder.

Hitch not raising or hitch raises slowly: Hydraulic pump failure. Replace or repair hydraulic oil pump. Main relief valve is faulty. Change relief valve. Faulty hydraulic spool valve. Repair or change hydraulic valve. Hydraulic cylinder is faulty. Change or repair hydraulic cylinder. Insufficient hydraulic fluid. Add fluid as required. Hydraulic oil filter is clogged. Hydraulic filter maintenance required. Excessive loading on the hitch. Load needs to be reduced.

Hitch cannot be dropped or dropping is too slow: Defective hydraulic cylinder. Replace or repair hydraulic cylinder. Not adjusted hydraulic control valve. Need to adjust. Hitch cross shaft is worn. Replace the shaft. Misadjusted hitch. Adjust the 3-point hitch.

3-point hitch jerks when lower or lift: Hydraulic fluid contamination. Change hydraulic fluid. Hydraulic pump malfunction. Install a new hydraulic oil pump. There is air in the hydraulic system. Bleed hydraulic system. Hydraulic control valve block is faulty. Replace or repair the valve. Damaged hydraulic cylinder. Repair or change hydraulic cylinder.

Massey Ferguson 1533 Steering Troubleshooting

Excessive play in steering: Steering column shaft or coupling is worn out. Replace faulty part. Steering pump failure. Replace or repair steering pump. Steering linkage joints are worn or loose. Repair or change steering linkage. Power steering control valve has wear or damage. Repair or replace the steering control valve.

Stiff steering: Air lock in the steering system. Bleed air. Dirty steering filter. Install new steering filter element. Steering oil level low. Add oil to steering system. Power steering control valve has malfunction or wear. Check and replace as required. Steering pump is faulty. Install a new steering pump. Steering pump control valve is stuck or worn. Replace or clean flow control valve. Damaged or incorrectly assembled steering column. Replace steering column or assemble correctly. Uneven wear on front tires. Replace the tires. Incorrect toe-in. Adjust toe-in wheels. Leaking steering cylinder. Replace worn cylinder seals or scratched piston rod.

Tractor pulls to right or left: Power steering control valve has wear or malfunction. Repair or replace the steering control valve. Steering cylinder is worn. Repair or change steering cylinder. Not adjusted toe-in. Check and adjust toe-in. Loose or worn steering linkage components. Inspect and replace as required. Front wheel bearings are worn or incorrectly adjusted. Replace or adjust the bearings correctly. Uneven tyre pressure. Inflate the tyres properly.

Massey Ferguson 1533 Electrical System Troubleshooting

Battery is not charging: Loose or corroded cable connections. Clean or tighten wiring connections. Battery terminal connectors are defective. Change terminal connectors. Bad cell in battery. Replace the battery. Defective or loose belt. Adjust belt tension or install a new belt.

Starter turns slowly: Low battery output voltage. Battery is drained, recharge it. Battery drains quickly. Service charging system or change battery. Terminals are faulty or battery cables are disconnected. Connect cables correctly or replace terminals.

Starter will not work: Battery is discharged or worn. Need to charge or replace the battery. Disconnected or improperly connected wiring harness. Inspect battery wiring harness and connect as required. Low battery output voltage. Low battery charging, charge as required. Starter motor failure. Repair or change starter.