________________________________________________________________________________

Massey Ferguson 2607H Troubleshooting

Massey Ferguson 2607H Engine Troubleshooting

Engine hard to start or doesn't start: Fuel filter element is dirty. Replace filter element. Air in the fuel system. Air bleeding. Fuel injection nozzles are faulty or clogged. Change fuel injection nozzles. Fuel injection pump malfunctioning. Install a new fuel pump or repair.

Engine shuts off suddenly during operation: Fuel injection pump timing is wrong. Adjust fuel injection pump as required. Fuel filter element is dirty. Replace filter element. Engine is cold. Normalize the temperature by warming up the engine.

Engine starts but immediately stalls: Fuel filter element is clogged. Replace filter element. Damaged fuel injection pump. Replacement or repair required. Plugged air cleaner. Change air filter element.

Engine overheated: Clogged radiator fins or damaged radiator cap. Install new cap or clean radiator. Low engine coolant. Add coolant fluid to cooling system and also check it for leaks. Fan belt is broken or worn. Belt replacement is recommended. Lack of engine oil. Fill up the engine oil.

Diesel power loss: Clogged or defective injection nozzles. Service or change injection nozzles. Fuel hoses or lines are clogged. Service fuel lines and hoses. Intake air restriction. Clean or replace the element. Defective cylinder head gasket. Gasket should be replaced.

Engine noises or knocks: Engine has not warmed up to the recommended temperature. Warm up the engine. Lack of engine oil. Add oil to the engine crankcase. Incorrect adjustment of fuel injection pump timing. Adjust as recommended. Worn or broken pistons. Have pistons replaced. Connecting rod misalignment or failure. Replace or align connecting rod.

Engine stops when idling: Low idle speed setting is incorrect. Correct low idle settings. Improper valve clearance. Check and adjust. Fuel injection pump malfunctioning. Repair or replace injection pump.

Oil pressure is insufficient: Engine oil insufficient. Fill the crankcase with oil. Oil pump is worn or damaged. Repair or change. Clogged oil filter element. Clean or replace engine oil filter element.

Massey Ferguson 2607H Transmission Troubleshooting

Excessive transmission noise: Improper backlash or worn gears. Adjust backlash properly or replace the gears. Shift forks are bent or worn out. Replace defective shift forks. Shaft splines are worn or damaged. Replace the shaft. Transmission oil insufficient. Fill the transmission housing to proper oil level. Worn or damaged bearings. Bearings replacement required. Transmission fluid is contaminated. Change the fluid.

Gears are hard to shift: Stuck or worn gear shift linkage. Lubricate or replace the shift linkage. Worn or unadjusted clutch. Change or adjust clutch. Shift forks are bent or worn out. Replace the shift forks. Defective parts in the gearshift mechanism. Replace defective parts.

Transmission oil pressure is insufficient: Insufficient transmission fluid. Need to add transmission fluid. Transmission oil filter element clogging (if equipped). Service or change transmission oil filter. Stuck relief valve. Replace valve as required.

Transmission fluid leakage: Worn seals or gaskets. Install new seal or gaskets. High transmission oil level. Correct the oil level.

Massey Ferguson 2607H Hydraulic System Troubleshooting

Hydraulics overheating: Incorrect hydraulic oil type. Use the correct type of hydraulic oil. Contaminated hydraulic fluid. Change hydraulic fluid. Air in hydraulic pipes. Bleed hydraulic pipes. Main relief valve is damaged. Change relief valve.

Low hydraulic system pressure: Hydraulic fluid is insufficient. Fill the system to proper hydraulic fluid level. Dirty hydraulic oil filter element. Clean the hydraulic filter or install new filter element. Hydraulic piping is leaking. Inspect the system for leaks and fix it. Not adjusted hydraulic spool valve. Need to adjust spool valve. Damaged hydraulic pump. Replace or repair hydraulic fluid pump. Hydraulic cylinder failure. Change or repair hydraulic cylinder.

Hitch can't lift or lifts too slowly: Hydraulic pump malfunction. Change or repair hydraulic oil pump. Defective main relief valve. Relief valve must be changed. Hydraulic control valve block is faulty. Replace or repair the valve. Defective hydraulic cylinder. Install a new hydraulic cylinder or repair it. Insufficient hydraulic oil. Need to add oil. Clogged hydraulic oil filter element. Clean or replace the hydraulic filter. Hitch is under excessive load. Reduce hitch load.

Hitch cannot be lowered or lowering is too slowly: Hydraulic cylinder is faulty. Change or repair hydraulic cylinder. Hydraulic spool valve is not set properly. Set the spool valve properly. Lift arm shaft is damaged. Install a new shaft. Unadjusted hitch. Adjustment is required.

Hitch jerks when drop or lift: Contaminated hydraulic oil. Change hydraulic oil. Defective hydraulic pump. Install a new hydraulic fluid pump. There is air in the hydraulic system. Bleed hydraulic system. Defective hydraulic control valve. Change or repair hydraulic valve. Hydraulic cylinder malfunction. Change or repair hydraulic cylinder.

Massey Ferguson 2607H Steering System Troubleshooting

Excessive play in steering: Steering column shaft or coupling has maximum wear. Change defective component. Faulty steering pump. Install a new hydraulic steering pump. Loose or worn steering linkage parts. Inspect and replace as required. Worn or defective steering control valve. Check and replace as required.

Difficult steering: Air in steering system. Air-bleed steering system. Dirty steering filter element. Clean steering filter element. Insufficient steering fluid. Fill up the steering fluid. Steering control valve is defective or worn. Inspect and replace as required. Worn steering pump. Repair or change steering pump. Steering pump control valve is worn or stuck. Service or change control valve. Defective or incorrectly mounted steering column. Change steering column or mount correctly. Front tyres are worn unevenly. Install new tyres. Incorrect toe-in. Adjust toe-in wheels. Steering cylinder is leaking. Replace worn seal sleeves or damaged piston rod.

Tractor pulls to left or right: Steering control valve has damage or wear. Inspect and replace as required. Defective steering cylinder. Repair or change hydraulic steering cylinder. Incorrect toe-in. Adjust toe-in wheels. Steering linkage assembly is worn or loose. Inspect and replace as required. Improperly adjusted or defective front hub bearings. Replace the bearings or adjust it properly. Front tires are worn unevenly. Install new tires.

Massey Ferguson 2607H Electrical Troubleshooting

Battery won’t charge: Wiring connections are corroded or loose. Service or tighten cable connections. Electrical terminal connectors are faulty. Replace terminal connectors. Battery faulty cell. Use a new battery. Belt is defective or loose. Change belt or adjust belt tension.

Starter turns slow: Battery power is low. Recharge the battery. Battery runs out quickly. Service or replace the battery. Faulty battery terminals or disconnected cables. Check battery wires and service or replace terminals.

Starter motor won't turn: Battery is drained or defective. Replace or charge as required. Wiring is incorrectly connected or disconnected. Inspect wiring and connect correctly. Low battery output. Battery is drained, charge it. Starter motor failing. Repair or change starter.