________________________________________________________________________________

Massey Ferguson GC2400 Troubleshooting

Massey Ferguson GC2400 Engine Troubleshooting

Engine hard to start or will not start: Fuel filter plugging. Filter maintenance required. Air in the fuel system. Air bleeding. Fuel injection nozzles are faulty or clogged. Inspect nozzles and replace if necessary. Defective fuel injection pump. Change pump or rebuild it.

Engine stops running suddenly: Fuel injection pump timing is not adjusted. Adjust as recommended. Fuel filter plugging. Change filter element. Engine is cold. Warm up the engine.

Engine starts but stalls suddenly: Clogged fuel filter. Clean the filter element. Fuel injection pump malfunctioning. Repair or install new pump. Dirty air filter. Clean or change.

Engine overheating: Radiator core is dirty or radiator cap is damaged. Clean radiator or change cap. Engine has a lack of coolant. Fill the cooling system and check components for leaks or other faults. Fan belt is worn or faulty. Belt replacement is recommended. Engine oil level is low. Fill up the oil to required level.

Diesel power loss: Clogged injection nozzle. Inspect nozzles and replace if necessary. Fuel lines or hoses clogging. Clean fuel hoses and lines. Air filter is clogged. Replace air filter element. Cylinder head gasket defective. Replace the gasket as required.

Abnormal engine knocking or noise: Low coolant temperature. Warm up the engine. Low engine oil level. Fill the crankcase with engine oil. Fuel injection pump timing is not adjusted. Use the correct fuel injection pump timing adjustment. Scored or worn pistons. Have pistons replaced. Connecting rod is not aligned or defective. Alignment procedure or replacement is required.

Engine stalls when idling: Too low idle RPM. Correct low idle adjustment. The valve clearance is not adjusted. Correct valve clearance needs to be set. Fuel injection pump damage. Repair or change injection pump.

Low oil pressure: Engine oil insufficient. Checking oil level and add if necessary. Oil pump is defective. Inspect and change as required. Oil filter element clogging. Service or change engine oil filter element.

Massey Ferguson GC2400 Hydrostatic Transmission Troubleshooting

Excessive HST transmission noise: Defective or not adjusted speed control pedal linkage. Change or adjust linkage. Transmission overloaded. Load needs to be reduced. Dirty transmission fluid or insufficient fluid level. Add fluid to the correct level or fill the transmission with fresh fluid. Relief valve is damaged. Install a new relief valve. Defective or worn transmission parts. Change or repair defective parts.

Transmission oil overheating: Transmission overloaded. Reduce the load is required. Plugged or defective cooling components. Check all cooling components and change or repair if required. Transmission fluid insufficient. Checking transmission fluid level and add if necessary. Plugged transmission oil filter. Service or replace the transmission oil filter.

Power is insufficient: Transmission fluid insufficient. Fill the transmission housing to proper fluid level. Relief valve failure. Replace relief valve as required. Worn or out of adjustment speed control linkage. Adjust or repair linkage.

Transmission oil leaking: Plugged oil return tube. Clean or replace return tube. Worn seals or gaskets. Replace worn seal or gaskets. High internal transmission housing pressure. Check transmission parts for damage or wear and replace if required.

Massey Ferguson GC2400 Hydraulic System Troubleshooting

Hydraulics overheating: Improper hydraulic fluid type. Use the proper type of hydraulic fluid. Hydraulic oil contamination. Change the oil. Air trapped in hydraulic system. Bleed air from system. Main relief valve failure. Relief valve must be changed.

Insufficient hydraulic fluid pressure: Hydraulic oil is insufficient. Checking hydraulic oil level and add if necessary. Dirty hydraulic fluid filter element. Service the hydraulic filter or change if required. Leaking hydraulic pipes. Inspect hydraulic system for leaks and repair it. Not adjusted hydraulic spool valve. Need to adjust spool valve. Hydraulic pump is defective. Install a new hydraulic fluid pump. Hydraulic cylinder malfunction. Install a new hydraulic cylinder or repair it.

Hitch does not raise or raises very slowly: Hydraulic pump not working. Repair or replace hydraulic fluid pump. Defective main relief valve. Relief valve replacement required. Defective hydraulic control valve block. Replace or repair the valve. Damaged hydraulic cylinder. Install a new hydraulic cylinder or repair it. Hydraulic oil is insufficient. Check and refill the hydraulic oil. Dirty hydraulic fluid filter. Change the hydraulic filter element or service if required. Excessive load on hitch. Reduce hitch load.

Hitch cannot be dropped or dropping is too slow: Hydraulic cylinder not working. Install a new hydraulic cylinder or repair it. Not adjusted hydraulic control valve. Need to adjust. Worn hitch rock shaft. Change the shaft. The hitch has not been adjusted. The 3-point hitch must be adjusted.

Hitch jerks when drop or lift: Contaminated hydraulic oil. Change hydraulic oil. Damaged hydraulic pump. Repair or replace hydraulic fluid pump. Air in hydraulic lines. Bleed hydraulic lines. Hydraulic spool valve is defective. Install a new hydraulic valve or repair it. Hydraulic cylinder malfunction. Repair or replace hydraulic cylinder.

Massey Ferguson GC2400 Steering System Troubleshooting

Excessive free play of steering wheel: Steering column coupling or shaft has maximum wear. Change defective part. Steering pump malfunction. Replace or repair steering pump. Loose or worn steering linkage parts. Repair or change steering linkage. Steering control valve has malfunction or wear. Inspect and change as required.

Steering wheel turns hard: Air lock in hydraulic steering system. Air-bleed steering system. Clogged steering filter element. Steering filter maintenance required. Steering oil insufficient. Check and refill steering oil. Worn or damaged steering control valve. Change or repair steering control valve if required. Steering pump not working. Check the hydraulic steering pump and change if necessary. Steering pump control valve is faulty or stuck. Clean or replace control valve. Improperly installed or damaged steering column. Install the steering column as required or replace it. Front tyres wear unevenly. Change the tyres. Not adjusted toe-in. Check and adjust toe-in. Steering cylinder leakage. Change worn piston seals or damaged piston rod.

Tractor is pulling to left or right: Steering control valve has damage or wear. Replace or repair steering control valve as required. Steering cylinder is worn. Replace or repair steering cylinder. Incorrect toe-in. Check and adjust toe-in. Worn or loose steering linkage assembly. Repair or change steering linkage. Defective or improperly adjusted front wheel bearings. Change or adjust bearings correctly. Uneven tire pressure. Inflate the tires properly.

Massey Ferguson GC2400 Electrical System Troubleshooting

Battery does not charge: Wiring connections are corroded or loose. Clean or tighten wiring connections. Battery terminal connectors are defective. Replace terminal connectors. Battery dead cell. Change the battery. Loose or defective belt. Belt needs to be adjusted or replaced.

Starter motor turns slow: Battery power is low. Battery is drained, recharge it. Battery runs out quickly. Service or change the battery. Bad battery terminals or disconnected wiring. Connect wires properly or change terminals.

Starter is not cranking: Battery is drained or worn. Battery needs to be recharged or replaced. Disconnected or incorrectly connected wires. Inspect battery wires and connect correctly. Low battery output. Low battery charging, charge as required. Starter motor failing. Starter needs to be replaced.