________________________________________________________________________________

New Holland T2410 Troubleshooting

New Holland T2410 Engine Troubleshooting

Engine starts hard or will not start: Clogged fuel filter. Clean the filter element. Air in the fuel system. Air bleeding. Clogged injection nozzle. Install a new kit of correctly balanced nozzles. Damaged fuel injection pump. Change pump or rebuild it.

Engine stalls while running: Wrong setting of fuel injection pump timing. Adjust fuel injection pump as required. Fuel filter element is clogged. Change filter element. Coolant temperature is low. Engine is not warmed up to the required temperature.

Diesel starts but immediately stops: Dirty fuel filter. Service the filter. Fuel injection pump is not operating properly. Rebuild or install a new injection pump. Dirty air cleaner. Replace air filter element.

Engine is overheated: Dirty radiator fins or faulty radiator cap. Replace cap or clean radiator. Low engine coolant. Add coolant fluid and inspect the cooling system for leaks. Fan belt is broken or worn. Install new fan belt. Engine oil level is insufficient. Need to add engine oil.

Engine is not running at maximum power: Fuel injection nozzles are clogged or faulty. Clean or change injection nozzles. Fuel hoses or lines are dirty. Clean fuel system lines and hoses. Clogged air filter. Clean or change. Cylinder-head gasket is broken. Install a new gasket.

Engine knocking or noise: Engine is cold. Engine is not warmed up to the required temperature. Engine oil level is low. Fill up the oil to required level. Wrong setting of fuel injection pump timing. Adjust the pump as required. Pistons are worn or broken. Have pistons replaced. Connecting rod is defective or not aligned. Alignment procedure or replacement is required.

Engine stops at idle: Incorrect low idle speed adjustment. Adjust as required. Valve out of adjustment. Have it adjusted. Fuel injection pump malfunctioning. Replace injection pump or repair it.

Low oil pressure: Oil level is low. Fill the crankcase with oil. Worn oil pump. Replace as required. Oil filter is clogged. Replace or service engine oil filter.

New Holland T2410 Transmission Troubleshooting

Transmission makes noise: Gears are defective or backlash is improper. Change worn gears or adjust backlash correctly. Worn or damaged gear shift forks. Shift forks need to be changed. Shaft splines are worn or stuck. Shaft need to be changed. Lack of transmission oil supply. Need to add transmission oil. Worn or broken bearings. Install new bearings. Transmission fluid is dirty. Change the fluid.

Gear shift is hard: Gear shift linkage is corroded or worn. Install new shift linkage. Worn or improperly adjusted clutch. Adjust or replace the clutch. Damaged or worn gear shift forks. Shift forks need to be changed. Defective parts in the gearshift mechanism. Replace defective parts.

Insufficient transmission oil pressure: Transmission oil insufficient. Fill up the transmission oil. Transmission fluid filter element is clogged (if equipped). Service or replace the transmission fluid filter. Relief valve is damaged. Replace valve as required.

External fluid leaks: Seals or gaskets are worn. Change defective gaskets or seal. High transmission fluid level. Drain the excess fluid.

New Holland T2410 Hydraulic System Troubleshooting

Hydraulics overheating: Hydraulic oil type is incorrect. Pour the correct type of oil. Hydraulic fluid contamination. Change hydraulic fluid. Air in the hydraulic system. Air bleeding. Main relief valve malfunction. Install a new relief valve.

Hydraulic fluid pressure is insufficient: Low hydraulic fluid level. Fill up the hydraulic fluid. Dirty hydraulic fluid filter. Replace hydraulic filter element or service if necessary. Leaking hydraulic pipes. Check the system and repair leaks. Incorrect adjusted hydraulic spool valve. Adjust the spool valve correctly. Damaged hydraulic pump. Replace or repair hydraulic fluid pump. Damaged hydraulic cylinder. Repair or install a new hydraulic cylinder.

3-point hitch can't lift or lifts too slowly: Damaged hydraulic pump. Change or repair hydraulic oil pump. Main relief valve is defective. Install a new relief valve. Damaged hydraulic spool valve. Repair or replace hydraulic valve. Defective hydraulic cylinder. Change or repair hydraulic cylinder. Insufficient hydraulic fluid. Fill the system to proper hydraulic fluid level. Dirty hydraulic fluid filter. Hydraulic filter maintenance required. Hitch is under excessive load. Reduce the load is required.

3-point hitch does not lower or lowers very slowly: Hydraulic cylinder failure. Change or repair hydraulic cylinder. Incorrect adjusted hydraulic spool valve. Adjust the spool valve correctly. Hitch rock shaft is damaged. Change the shaft. The three-point hitch is not adjusted. The 3-point hitch must be adjusted.

Hitch drop or lift is jerky: Hydraulic oil is dirty. Hydraulic oil change required. Hydraulic pump failure. Install a new hydraulic fluid pump. Air in hydraulic pipes. Bleed hydraulic pipes. Defective hydraulic spool valve. Install a new valve or repair it. Hydraulic cylinder malfunction. Replace or repair hydraulic cylinder.

New Holland T2410 Steering Troubleshooting

Steering wheel free play is excessive: Steering column coupling or shaft is worn. Replace defective part. Worn steering pump. Install a new hydraulic steering pump. Steering linkage joints are worn or loose. Replace or repair steering linkage. Hydrostatic steering unit has malfunction or wear. Check and replace as required.

Steering is hard: Air lock in the steering system. Bleed air. Steering filter element is clogged. Service or replace the steering filter. Steering fluid insufficient. Check and refill steering fluid. Hydrostatic steering unit has malfunction or wear. Check and replace as required. Hydraulic steering pump is defective. Check the steering pump and replace if necessary. Steering pump control valve is faulty or stuck. Change or flush control valve. Defective or incorrectly mounted steering column. Change steering column or mount correctly. Tire pressure is uneven. Adjust the tire pressure. Not adjusted toe-in. Check toe-in and correct. Steering cylinder leakage. Replace scratched piston rod or worn cylinder seals.

Tractor pulls to right or left: Hydrostatic steering unit has wear or malfunction. Change or repair steering unit if required. Steering cylinder damage. Change or repair steering cylinder. Not adjusted toe-in. Check toe-in and correct. Loose or worn steering linkage components. Replace or repair steering linkage. Defective or improperly adjusted front wheel bearings. Adjust properly or replace bearings. Front tyres are worn unevenly. Install new tyres.

New Holland T2410 Electrical Troubleshooting

Battery does not charge: Loose or corroded electrical wiring connections. Clean or tighten connections. Faulty electrical terminal connectors. Install new terminal connectors. Bad cell in battery. Battery replacement required. Defective or loose belt. Adjust belt tension or change the belt.

Starter motor turns slow: Low battery capacity. Charge the battery. Battery runs out quickly. Service charging system or install new battery. Bad terminals or disconnected battery cables. Check wiring and clean or replace terminals.

Starter does not work: Battery is low or faulty. Battery needs to be recharged or replaced. Battery wiring is disconnected or improperly connected. Inspect wiring and connect as required. Battery power is low. Battery is drained, charge it. Starter motor failure. Starter needs to be changed.