________________________________________________________________________________

John Deere 2032R Attachments

John Deere 2032R Front End Loader

H130 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - JD 2032R
Bucket pin-on used - 1250 mm (49 in.)
Bucket weight - 50.6 kg (111.3 lb)
Lift capacity at full height (at pivot) - 368 kg (810 lb)
Lift capacity at full height (at 500 mm ahead of pivot) - 257 kg (565 lb)
Lift capacity at 59 in. (1500 mm) (at pivot) - 428 kg (942 lb)
Lift capacity at 59 in. (1500 mm) (at 500 mm ahead of pivot) - 312 kg (686 lb)
Boom breakout force (at pivot) - 792 kg (1742.4 lb)
Boom breakout force (at 500 mm ahead of pivot) - 553 kg (1216.6 lb)
Bucket rollback force capacity (at maximum height) - 612 kgf (1346.4 lbf)
Bucket rollback force capacity (at 59-in. 1500-mm) lift height - 728 kgf (1601.6 lbf)
Bucket rollback force capacity (at ground-level line) - 710 kgf (1562 lbf)
Maximum lift height - 1865 mm (73.4 in.)
Clearance (at full height - bucket level) - 1699 mm (66.9 in.)
Clearance (at full height - bucket dumped) - 1426 mm (56.1 in.)
Overall length - 2.8 m (9.1 ft)
Overall height in carry position - 1.1 m (3.5 ft)
Digging depth - 231 mm (9.1 in.)
Reach (at maximum height) - 727 mm (28.6 in.)
Reach (at ground level - bucket level) - 1332 mm (52.4 in.)
Dump bucket angle - 38 degree
Rollback bucket angle - 32 degree
Dump bucket angle, ground - 111 degree
Loader raise - 5.56 seconds
Loader lower - 3.39 seconds
Bucket dump (w/o regen / w/ regen) - 5.56/2.17 seconds
Bucket rollback - 3.39 seconds

Installing Hitch Pin Bushings on Ballast Box for Category 1 Quick Coupler Hitch - Install bushings on both hitch pins. Install bushing over hitch pin with cross hole. Install bushing. Align holes in bushings with hole in hitch pin and install spring pin. Assemble bushings. Insert center link pin through ballast box mast and bushing assembly. Fasten with quick-lock pin.

Attaching Ballast Box to John Deere 2032R Tractor with Three-Point Hitch - Back up JD 2032R tractor to ballast box with hitch points approximately in alignment. Engage tractor parking brake and/or place transmission in PARK. Shut off tractor engine and remove key. Attach tractor draft links. Fasten with quick-lock pins (stored on tractor draft links). Align center link with upper hole in ballast box mounting straps and install center link mounting hardware. Start engine. Slowly pull hitch control lever to raise ballast box. Check for interference. Lower hitch to ground and adjust center link and/or lift links if necessary.

Attaching Ballast Box to John Deere 2032R Tractor with Quick Coupler Hitch - Slowly push hitch control lever to lower hitch until quick coupler hooks are lower than ballast box hitch pins. Back up tractor to ballast box. Check spring loaded clips on quick coupler to be sure latches are free and working properly. Make sure latch control levers are down. Slowly pull hitch control lever to engage ballast box hitch pins in quick coupler hooks. Raise ballast box and check for interference. Lower ballast box to ground and adjust if necessary.

Attach H130 Loader - Drive 2032R tractor slowly, straight into John Deere H130 loader. Align masts with mounting frames. Engage tractor parking brake and place transmission in PARK. Shut off tractor engine and remove key. Make sure hoses are routed through hose guide. Connect hoses using color-coded dust caps matching numbers and colors on decal by coupler plate. It may be necessary to drive tractor forward slowly to keep masts/frames in line while performing the following procedures. Be sure bushing on mounting frame is aligned with notch in masts. Start engine.

Release parking brake and/or place transmission in NEUTRAL. Make sure masts are fully seated on mounting frames. Slowly retract lift cylinders. Masts will lower onto mounting frames and parking stand will raise up below weight bracket. Dump bucket 10-20° and retract lift cylinders until H130 loader masts move back and latches lock over mounting frame bushings. Extend lift cylinders and lift bucket from ground to ensure loader is properly mounted. Add appropriate ballast. Engage tractor parking brake and/or place transmission in PARK. Shut off tractor engine and remove key.

220R Loader Specifications

Type of Attachment - Front End Loader
Compatibility - JD 2032R
Height (to pin) - 85 in. (215 cm)
Clearance, dumped bucket - 66 in. (167 cm)
Dump reach - 30 in. (76 cm)
Dump angle - 36 degrees
Clearance, level bucket - 79 in. (200 cm)
Reach at ground - 51 in. (129 cm)
Breakout force (at pin) - 1949 lb (884 kg)
Breakout force (at 500mm) - 1360 lb (616 kg)
Breakout force (bucket) - 2138 lb (969 kg)
Lift to full height (at pin) - 1120 lb (508 kg)
Lift to full height (at 500mm) - 803 lb (364 kg)
Lift to 1.5m (at pin) - 1269 lb (575 kg)
Lift to 1.5m (at 500mm) - 979 lb (444 kg)
Bucket width - 49 in. (124 cm) / 57 in. (144 cm)

John Deere 2032R Backhoe

46 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 2032R
Digging depth - 6-ft. 6-in. (1.98 m)
Loading height (bucket at 60 degrees) - 5-ft. 0-in. (1.5 m)
Reach from center line of swing pivot - 8-ft. 5-in. (2.57 m)
Transport height - 5-ft. 0-in. (1.5 m)
Loading reach (bucket at 60 degrees) - 3-ft. 2-in. (.97 m)
Transport overhang - 3-ft. 5-in. (1.04 m)
Undercut - 2-ft. 4-in. (0.71 m)
Swing arc - 180 degrees
Weight - 896 lb. (407 kg)
Bucket Rotation - 180 degrees
Stabilizers spread width, up - 3-ft. 11-in. (1.19 m)
Stabilizers spread width, down - 6-ft. 6-in. (1.98 m)
Boom lift capacity - 348 lb. (158 kg)
Dipperstick digging force - 1250 lb. (5560 N)
Bucket digging force - 2450 lb. (10900 N)
Bucket control main relief valve pressure - 2250 psi (15510 kPa)

Bucket Width - 13-in. (330 mm)
Struck Capacity - 0.77 cu. ft. (0.022 cu. m)
Heaped Capacity - 1.04 cu. ft. (0.029 cu. m)
Weight - 58 lb. (26 kg)
Bucket Width - 20-in. (508 mm)
Struck Capacity - 1.26 cu. ft. (0.036 cu. m)
Heaped Capacity - 1.74 cu. ft. (0.049 cu. m)
Weight - 67 lb. (30 kg)
Bucket Width - 24-in. (610 mm)
Struck Capacity - 1.54 cu. ft. (0.044 cu. m)
Heaped Capacity - 2.14 cu. ft. (0.061 cu. m)
Weight - 78 lb. (35 kg)

Assemble John Deere 46 Backhoe - Follow Preparing JD 2032R Tractor to remove 3-point hitch, install front hangers, install rear mounting support, and align backhoe subframe before you assemble 46 backhoe. Use proper lifting device to raise and support backhoe mainframe. Align subframe with holes in mainframe, and install six 3/4 x 2-1/2 in. cap screws, twelve washers, and locknuts. Tighten to 379 Nm (280 lbft).

Install Stabilizers - Pivot pins on 46 backhoe are installed with either cotter pins or retainers. Retainer is installed in pivot pin with bolt, 11/32-in. washer, and 5/16-in. locknut. Remove pivot pins stored in stabilizers. Remove pivot pins securing cylinders to backhoe, and remove cylinders. Install both stabilizers on backhoe with pivot pin. Install cotter pins or retainers in pivot pins. Install both cylinders on backhoe and stabilizers with pivot pins. Install cotter pins or retainers in pivot pins. Route hydraulic hoses: Route cylinder rod end hoses above the pivot pins, and route cylinder base end hoses below the pivot pins. Lubricate all grease fittings and pivot points before operating backhoe.

Install Bucket - Grease both sides of two 1-1/32 x 1-1/2 in. washers and install between bucket and dipperstick on both sides of dipperstick. Install pivot pin through bucket, washers, and dipperstick. Install two retainers in pivot pin with hardware. Remove shipping wire holding link to dipperstick. Pivot the bucket back and install pivot pin through bucket and link. Install two 1-1/32 x 1-1/2 in. washers between bucket and link if needed. Install two retainers in pivot pin with hardware. Lubricate all grease fittings and pivot points before operating backhoe. Installing Slow Moving Vehicle (SMV) Sign Install SMV sign: Remove SMV sign shipped with backhoe, and install into bracket on the backhoe bucket cylinder.

John Deere 2032R Mower Deck

62-inch Mower Deck Specifications

Model - 62D AutoConnect Mid-Mount Mower
Mower Type - Mulch or Side Discharge
Compatibility - JD 2032R
Cutting Blades - 3
Overall Width - 940 mm (37 in.)
Overall Length - 1910 mm (75.3 in.)
Cutting Height - 26mm-150mm (1-6 in.)
Cutting Width - 1570 mm (62 inch)
Weight - 125 kg (275 lb)
Blade Bolt Torque - 68 Nm (50 lb-ft)
Gearbox Oil Capacity - 136ml (4.6 oz)

72-inch Mower Deck Specifications

Model - 72" Mid-Mount Mower
Mower Type - Mulch or Side Discharge
Compatibility - JD 2032R
Cutting Blades - 3
Overall Width - 2190 mm (86 in.)
Overall Length - 1140 mm (45 in.)
Cutting Height - 38-127 mm (1-1/2 -5 in.)
Cutting Width - 1800 mm (72.8 inch)
Mower Weight - 156 kg (345 lb)
Blade Bolt Torque - 122 Nm (90 lb-ft)
Gearbox Oil Capacity - 136 ml (4.6 oz)

Install Discharge Chute - Install rod: 72" Mower does not have access hole. Install rod though first chute hole, first mower deck attaching point, second chute hole and spring. Correct placement of spring is necessary to provide downward pressure on discharge chute. Insert long end of spring through hole in discharge chute and push pin into spring. Unwind short end of spring until it can be placed on top of 72-inch mower deck. Insert rod through remaining mower deck and discharge chute attaching points. Verify that spring placement is correct by ensuring discharge chute has downward pressure. Install roll pins at both ends of rod. Install one roll pin.

John Deere 2032R Snowblower

54 Inch Snow blower Specifications

Snowblower Type - Front Mount
Compatibility - JD 2032R
Clearing Width - 1.40 m (54 in.)
Height to Top of Spout - 78 cm (30-5/8 in.)
Length - 69 cm (27 in.)
Lift Height - 279 mm (11 in.)
Net Weight - 113 kg (250 lb.)
Scraper Blade Reversible and Replaceable - 1.3 m (59-15/16 in.)
Discharge Chute Control - Hydraulic
Discharge Chute Rotation - 100° to each side
Snowblower Drive - Splined coupler shaft to gear case
Snowblower Lift - Hydraulic
Rotor Length - 1 m (39-3/8 in.)
Auger Speed - 176 rpm
Auger Diameter - 40.6 cm (16 in.)
Impeller Speed - 950 rpm
Impeller Diameter - 40.3 cm (15.5 in.)
Drive - Gear case to roller chain
Bearings - Sealed ball bearings

Install Discharge Chute and Cables - Apply grease on the bottom and inside flange of discharge chute. Place discharge chute over auger opening on housing. Install three clips with six self tapping bolts. Tighten bolts. Chute should rotate freely after tightening. Lay cables over housing. Remove cable shield and verify that chute cables are still on pulleys. Rotate chute to right. Stand behind 54" snow blower. Take right cable and wrap counterclockwise around chute. Use locking pliers to pull cable tight around threaded stud, and behind nut and washer. Tighten nut. Wrap left cable clockwise around chute. Use locking pliers to pull cable tight around threaded stud, and behind nut and washer. Tighten nut. Tuck excess ends of cables under cable. Install cable shield.

Install 54" snowblower Driveshaft - Lubricate grease fittings. Install key in gearbox shaft groove. Apply recommended grease to sprocket shaft. Align groove in driveshaft with key on sprocket shaft and push driveshaft on sprocket shaft. Align holes on sprocket shaft with holes in driveshaft, and install rolled pin through both shafts. Install wire through rolled pin and twist both ends of wire together a minimum of three turns.

John Deere 2032R Front Blade

54 Inch Blade Specifications

Compatibility - JD 2032R
Blade Width, Straight - 54 in. (1.4 m)
Blade Width, Angled 15° - 52-3/16 in. (1.3 m)
Blade Width, Angled 27° - 48-1/8 in. (1.2 m)
Angling Positions, Right and Left - 0-27 degrees
Blade Trip - Spring Trip
Blade Float - Hydraulic

Installing 54-inch Front Blade to Front Hitch - Park machine safely. Insert locking pin assembly in rear hole on front hitch and fasten with spring locking pin. Place blade on a level surface. Lower front hitch. Locking pin lever on each side of front hitch bracket must be in the unlatched position. Move machine forward slowly until slot on front hitch bracket lines up with pin on front blade. Raise front hitch until slot locks in place under pin and locking pins click into hitch bracket. Lower front blade to the ground.

Checking Hydraulic Hoses and Fluid Level - Remove transaxle hydraulic fluid dip stick. Check fluid level. Add fluid if necessary. Replace dip stick. Start engine. Move hydraulic control levers back and forth to check for leaks.