________________________________________________________________________________

John Deere 1023E Tractor Specs Overview

John Deere 1023E Tractor Engine

Engine Model - Yanmar 3TNM72
Engine Power, Rated, hp (kW) - 22.4 (16.5)
Engine Speed, rpm - 3200
Power Boost, hp (kW) - No boost
Fuel Tank, gal (L) - 5.6 (21.2)
Cylinders - 3
Displacement, cu in (L) - 55.1 (0.903)
Engine Bore, in (mm) - 2.83 (72)
Engine Stroke, in (mm) - 2.91 (74)
Block Design, Replaceable Liners - Cast-in-block
Aspiration, Turbocharged or Naturally Aspirated - Natural

Fuel System

Fuel System Description - In-Line Pump System
Fuel System Control - Mechanical
Fuel Injection to combustion chamber - Indirect

Emission and Exhaust Treatment

Emission Level - Tier 4 Interim
Exhaust Pipe - Horizontal

Cooling System

Fan Drive Type - Belt

Tractor Electrical System

System Rating, Volts - 12
Alternator Rating, Amps - 40

John Deere 1023E Tractor Transmission

Description - Hydrostatic, 2 range
Transmission Type - Hydrostatic
Forward / Reverse Speeds - Infinite, 2 ranges
Maximum Speed Forward, mph (kph) - 9.1 (14.6)
Creeper Range - Yes, hydrostatic
Shuttle (Forward-Reverse) - Yes

John Deere 1023E Tractor PTO (Power take off)

PTO Horsepower, hp (kW) - 15.3 (11.4)
PTO Speeds, rpm - 540 Rear; 2100 Mid
PTO operational Type - Independent

Wheels

Drive Wheels - 4WD
Tractor Steering Configuration - Front Steer

JD 1023E Tractor Rear Axle

Final Drive - Spur Gear
Axle Output End - Flange
Axle Bar Diameter, in (mm) - No bar axle

Brakes

Brake Type - Wet disk

John Deere 1023E Tractor Hydraulic System

Hydraulic System Type - Open center
Main Hydraulic Pump Type - Gear
Standard Pump Flow, gpm (Lpm) - 3.5 (13.2)
Standard Remote Valves - 2

3-Point Hitch Features

3-Point Hitch Category - Limited Category 1

Draft Sensing or Lift Control - Position Control

3-Point Hitch Lift Capacity

Standard Lift Capacity 24 Inches behind pin, lb (kg) - 681 (309)

Drawbar

Drawbar Description - Fixed hitch plate

Wheelbase

Wheelbase, 4WD, in (mm) - 57.1 (1450)

Tire Size

Front Tire Size, 4WD - 18x8.5-10, 4PR, R4
Rear Tire Size - 26x12-12, 4PR, R4

Easy operation four-wheel drive (4WD) and power steering.

Both 4WD and power steering are standard equipment on tractor. This combination allows for excellent maneuverability and ease of operation of the tractor.

Narrow overall width allows the JD 1023E Tractor to work in tight areas where most compact tractors just can't fit, yet the 144.8 cm (57-in.) wheel base and 119.4 cm (47-in.) overall width gives great stability for all type of terrains.

Power steering means fewer turns of the steering wheel than manual steering; especially valuable when mowing around obstacles or when the tractor is used with a front loader.

High horsepower-to-weight ratio makes the John Deere 1023E Tractor a good choice for a variety of tasks; overall tractor weight reduces ground compaction and makes your machine an excellent mowing tractor.

The power take-off (PTO) is a fully-independent PTO on tractor, allowing engaging and disengaging of the PTO without stopping movement. This is important when driving across obstacles such as driveways while mowing.

Hydrostatic transmission (HST) John Deere 1023E Tractor with Twin Touch foot controls

Two sets of right-hand couplers can operate two hydraulic functions (such as loader bucket cylinders and boom cylinders).

The right-hand-side mid-mounted couplers are positioned to allow easy access for hooking and unhooking hydraulic lines.

Large 0.64 cm (1/4-in.) diameter couplers are used to maximize oil flow to implements.

Hydraulics have excellent feather ability for smooth operation.

Float position. Regenerative position

PTO operation configuration: Engine, Engine clutch, Transmission, Wheel, PTO clutch, PTO selection, Rear PTO, Mid PTO

JD 1023E Tractor Service Transmission

Changing Front Axle Oil

- Operate machine to warm front axle oil.