________________________________________________________________________________

New Holland T6080 Troubleshooting

New Holland T6080 Diesel Engine Troubleshooting

Engine starts hard or doesn't start: Fuel filter element is clogged. Service the filter. Air in the fuel lines. Bleed the fuel lines. Fuel injection nozzles are dirty or defective. Test injection nozzles and change if necessary. Defective fuel injection pump. Install a new pump or rebuild.

Engine stalls while running: Incorrect adjustment of fuel injection pump timing. Adjust according to specifications. Fuel filter plugged. Replace the filter element. Coolant temperature is low. Warm up to required temperature.

Engine starts but then stalls: Dirty fuel filter. Install new filter element. Fuel injection pump failure. Replace or repair injection pump. Clogged air cleaner. Service or replace the air filter.

Engine overheated: Clogged radiator fins or leaking radiator cap. Clean radiator or change cap. Low coolant level. Top up coolant fluid and check system for leaks. Damaged or worn fan belt. Fan belt must be replaced. Engine oil level low. Fill up the oil to required level.

Diesel engine loses power: Clogged or burnt injection nozzle. Test injection nozzles and change if necessary. Dirty fuel lines or hoses. Clean fuel system hoses and lines. Plugged air filter. Air filter maintenance required. Cylinder-head gasket is broken. Replace the gasket as required.

Engine noises or knocks: Engine is not preheated. Warm up engine as required. Lack of engine oil. Check oil level and add oil as required. Improper fuel injection timing. Adjust as recommended. Worn or scored pistons. Pistons replacement required. Connecting rod is not aligned or worn. Connecting rod must be aligned or replaced.

Engine stalls when idling: Low idle speed adjustment is incorrect. Correct low idle adjustment. Incorrect valve clearance. Need to adjust valve clearance. Fuel injection pump is broken. Replace injection pump or repair it.

Insufficient oil pressure: Engine oil level low. Add oil to the engine crankcase. Oil pump failure. Replace as required. Oil filter is dirty. Service or change engine oil filter element.

New Holland T6080 Transmission Troubleshooting

Transmission makes noise: Gears are defective or backlash is improper. Replace defective gears or set backlash properly. Shift forks are bent or worn out. Shift forks need to be changed. Shaft splines are stuck or worn out. Shaft need to be changed. Transmission oil insufficient. Fill the transmission housing with oil. Worn or cracked bearings. Bearings need to be replaced. Transmission oil is dirty. Change the oil.

Hard shifts: Stuck or worn gear shift linkage. Install new shift linkage. Improperly adjusted or worn clutch. Adjust correctly or replace. Damaged or worn gear shift forks. Change the shift forks. Gearshift mechanism malfunction. Identify and replace failed parts.

Low transmission oil pressure: Transmission oil level is low. Fill the transmission housing to proper oil level. Dirty transmission fluid filter (if fitted). Clean or change transmission fluid filter. Relief valve is damaged. Change relief valve.

Transmission fluid leaking: Damaged gaskets or seals. Install new seal or gaskets. Too much fluid in transmission. Excess fluid must be drained.

New Holland T6080 Hydraulics Troubleshooting

Hydraulic system is too hot: Wrong hydraulic fluid type. Pour the proper type of fluid. Hydraulic fluid is contaminated. Fill up with new hydraulic fluid. There is air in the hydraulic system. Bleed hydraulic system. Main relief valve is defective. Relief valve replacement required.

Hydraulic fluid pressure too low: Hydraulic oil is insufficient. Checking hydraulic oil level and add if necessary. Clogged hydraulic oil filter element. Clean the hydraulic filter element or replace if necessary. Leaking hydraulic pipes. Check the hydraulic system and fix leaks. Hydraulic control valve block is set improperly. Set properly. Defective hydraulic pump. Change or repair hydraulic fluid pump. Hydraulic cylinder is defective. Install a new hydraulic cylinder or repair it.

3-point hitch cannot be raised or raising is too slowly: Hydraulic pump not working. Repair or replace hydraulic oil pump. Damaged main relief valve. Relief valve need to be replaced. Hydraulic spool valve block is defective. Repair or change hydraulic valve. Defective hydraulic cylinder. Change or repair hydraulic cylinder. Hydraulic oil level low. Need to add oil. Clogged hydraulic fluid filter. Replace hydraulic filter element or service if necessary. Hitch is under excessive load. Reduce loading.

3-point hitch cannot be lowered or lowering is too slowly: Broken hydraulic cylinder. Repair or install a new hydraulic cylinder. Hydraulic control valve block is set improperly. Set properly. Damaged hitch cross shaft. Install a new shaft. The three-point hitch is not adjusted. Adjustment is required.

Jerky lowering or lifting of the hitch: Hydraulic oil contamination. Change the oil. Defective hydraulic pump. Change or repair hydraulic oil pump. Air in hydraulic lines. Bleed hydraulic lines. Defective hydraulic control valve block. Repair or replace the valve. Hydraulic cylinder malfunction. Repair or change hydraulic cylinder.

New Holland T6080 Steering System Troubleshooting

Excessive play in steering: Steering column shaft or coupling is worn out. Replace defective component. Steering pump is worn. Replace or repair steering pump. Steering linkage joints are worn or loose. Inspect and change as required. Defective or worn hydrostatic steering unit. Inspect and replace as required.

Steering wheel is hard to turn: Air trapped inside steering system. Need to bleed air. Dirty steering filter. Replace steering filter element. Steering oil level low. Add oil to steering system. Hydrostatic steering unit has damage or wear. Inspect and replace as required. Steering pump is worn. Steering pump needs to be repaired or replaced. Stuck or worn pump flow control valve. Clean or replace control valve. Defective or incorrectly mounted steering column. Change steering column or mount correctly. Uneven tire pressure. Inflate the tires properly. Not adjusted toe-in. Adjust toe-in properly. Steering cylinder leaks. Replace worn cylinder seals or scratched piston rod.

Front wheels wander to left or right: Hydrostatic steering unit is defective or worn. Inspect and change as required. Faulty steering cylinder. Repair or replace hydraulic steering cylinder. Improper toe-in. Adjust toe-in properly. Steering linkage parts are loose or worn. Inspect and change as required. Improperly adjusted or defective front hub bearings. Adjust properly or replace bearings. Uneven tire pressure. Inflate the tires properly.

New Holland T6080 Electrical Troubleshooting

Battery does not charge: Wiring connections are loose or corroded. Service or tighten cable connections. Faulty battery terminal clamps. Replace terminal clamps. Worn-out battery. Install a new battery. Defective or loose belt. Replace belt or adjust belt tension.

Starter motor turns slow: Battery capacity is low. Battery is drained, recharge it. Battery will not hold charge. Service charging system or change battery. Corroded battery terminals or disconnected wires. Check wire connections and change or service terminals.

Starter doesn't crank: Battery is drained or defective. Charge or change the battery. Battery wiring is disconnected or improperly connected. Inspect wiring and connect as required. Battery voltage is low. Battery needs to be recharged. Starter motor is faulty. Starter should be replaced.