________________________________________________________________________________

John Deere 1026R Attachments

John Deere 1026R Front End Loader

H120 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 1026R
Bucket Width - 1250 mm (49 in)
Bucket Mass - 51 kg (112 lb)
Hydraulic System Rated Flow - 13.2 L/min (2.9 gal/min)
Hydraulic System Maximum Pressure - 13700 kPa (137 bar) (1987 psi)
Loader Raise Time - 4.0 sec.
Loader Lower Time - 2.5 sec.
Bucket Dump Time - 5.7 sec.
Bucket Rollback Time - 3.5 sec.
Maximum Lift Height To Pivot Pin - 1809 mm (71 in)
Bucket Level Clearance - 1653 mm (65 in)
Bucket Dumped Clearance - 1371 mm (54 in)
Overall Length - 2626 mm (103 in)
Digging Depth - 101 mm (4 in)
Reach At Maximum Lift Height with Bucket Dumped - 571 mm (22.5 in)
Bucket Reach on Ground with Bucket Leveled - 1176 mm (46 in)
Maximum Dump Angle - 40°
Maximum Dump Angle at Ground - 114°
Maximum Rollback Angle - 31°
Lift Capacity To Maximum Height at Pivot Point - 319 kg (703 lb)
Lift Capacity To Maximum Height - 232 kg (512 lb)
Lift Capacity To 1500 mm (59 in) at pivot pin - 331 kg (730 lb)
Lift Capacity To 1500 mm (59 in) - 265 kg (584 lb)
Breakout Force At Pivot Point - 782 kg-force (1724 lbf)
Breakout Force At 500 mm forward of pivot point - 595 kg-force (1312 lbf)
Bucket Rollback Force At maximum height - 763 kg-force (1682 lbf)
Bucket Rollback Force At 1500 mm (59 in) lift height - 789 kg-force (1740 lbf)
Bucket Rollback Force At Ground Level Line - 867 kg-force (1912 lbf)

Attaching H120 loader to John Deere 1026R tractor - Ensure that all hydraulic fittings are free of dirt. Start the engine. Drive forward and position JD 1026R tractor between the loader booms. Apply the park brake and shut off the engine. Place the hydraulic hose bundle in the guide. Route the hoses over the mounting frame and connect hydraulic couplers using color-coded caps and plugs.

Key A - Dust Cap/Plug Color - Black. Hydraulic Function - Bucket Cylinder-Rod End
Key B - Dust Cap/Plug Color - Yellow. Hydraulic Function - Bucket Cylinder-Head End
Key C - Dust Cap/Plug Color - Blue. Hydraulic Function - Lift Cylinder-Head End
Key D - Dust Cap/Plug Color - Red. Hydraulic Function - Lift Cylinder-Rod End

Connect color-coded caps and plugs together. Retract lift cylinders until mast pins are seated in saddles on both sides. As masts are tilted back, mounting frame pins open latches and then return them to the locked position. Parking stand automatically raises to the stored position under the tractor during the procedure. Dump the bucket and retract lift cylinders until the loader masts move back and latches contact mounting frame pins, causing them to open. Continue retracting lift cylinders until latches return to the locked position. Verify that latches are fully engaged on both sides and parking stand is in the stored position under the tractor frame.

Detach JD H120 Loader - Remove the ballast box. Ensure that the John Deere H120 loader is equipped with a materials bucket. Start the engine. Release the park brake or place the transmission in NEUTRAL. Dump the bucket approximately 20° and lower the boom to the ground. To raise the front wheels 25-50 mm (1-2 in) off the ground, retract lift cylinders. Push upward on the handle to disengage the latch. Repeat on the opposite side. Extend lift cylinders until the parking stand contacts the ground and mast pins lift out of mounting frame saddles.
Retract bucket cylinders until latches automatically return to the locked (down) position.

Engage 1026R tractor park brake or place the transmission in PARK. Shut off engine and remove ignition key. Relieve the hydraulic pressure from the system. Move the hydraulic control lever back-and-forth and side-to-side several times. Disconnect hydraulic hoses from the tractor: Push back the collar on the female coupler and pull out the male coupler. Install the dust plug in the female coupler and cap on the male coupler. Repeat for the remaining couplers. Remove the hydraulic hose bundle from the guide on the inside right-hand mast. Store the hoses on the lift cylinder. Slowly back the tractor away from the loader.

Detach and Attach Quik-Change Attachments - The procedure is the same for all attachments. Start the engine. Release the park brake and place the transmission in NEUTRAL. Roll back the bucket slightly and raise the boom
approximately 460 mm (18 in) above the ground. Engage the park brake and place the transmission in PARK. Shut off engine and remove ignition key. Remove the quick-lock pin from each side of the bucket. Store quick-lock pins in the storage position. Start the engine. Extend bucket cylinders until the bucket pin releases from the holder strap on each side of the bucket. Lower the boom, place the transmission in REVERSE and move away from the bucket. Holder releases from the hook on each side of the bucket. Set the park brake or place the transmission in PARK. Shut off engine and remove ignition key. Attach in reverse order.

120R Loader Specifications

Type of Attachment - Front End Loader
Compatibility - JD 1026R
Lift capacity at full height (at pivot/at 50 cm) - 342 kg (754 lb) / 236 kg (520 lb)
Lift capacity at 1500 mm (at pivot/at 50 cm) - 337 kg (743 lb) / 263 kg (580 lb)
Boom breakout force (at pivot/at 50 cm) - 826 kg (1823 lb) / 599 kg (1320 lb)
Bucket rollback force capacity (at max height/at 150 cm lift height) - 741 kg (1634 lb) / 770 kg (1700 lb)
Maximum lift height - 183 cm (72 in.)
Overall length - 279 cm (107.9 in.)
Digging depth - 9 cm (3.2 in.)
Reach (at max height/at ground-bucket) 63 cm (24.7 in.) / 119 cm (46.7 in.)
Bucket used - General Material 1250
Bucket weight - 70.2 kg (154 lb)

John Deere 1026R Backhoe

260 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 1026R
Digging Depth - 189 cm (74.5 in.)
Swing Arc - 150 degree
Weight with 16 in. Bucket - 277 kg (610 lb)
Loading Height (bucket at 60 degrees) - 150 cm (60 in.)
Reach From Center Line of Swing Pivot - 264 cm (104 in.)
Transport Height - 170 cm (66 in.)
Bucket Rotation - 180 degree
Loading Reach (bucket at 60 degree) - 84 cm (33 in.)
Transport Overhang - 94 cm (37 in.)
Undercut - 43 cm (17 in.)
Stabilizers Spread Width (Raised) - 147 cm (58 in.)
Stabilizers Spread Width (Lowered) - 188 cm (74 in.)
Boom Lift Capacity - 129 kg (285 lb)
SAE Dipperstick Digging Force - 5,28 kN (1187 lb)
SAE Bucket Digging Force - 9,1 kN (2036 lb)
Digging Depth - 61 cm (24 in.) flat bottom.

Buckets

Bucket Width - 300 mm (12 in.)
SAE Struck Capacity - 0.019 m3 (0.66 ft3)
Heaped Capacity - 0.022 m3 (0.76 ft3)
Bucket Width - 410 mm (16 in.)
SAE Struck Capacity - 0.025 m3 (0.90 ft3)
Heaped Capacity - 0.030 m3 (1.06 ft3)

Attaching 260 Backhoe To John Deere 1026R Tractor - Back JD 1026R tractor up until approximately 20 cm (8 in.) from backhoe. Park tractor safely. Route backhoe hydraulic hoses through hose guide and connect to hoses from tractor. Remove backhoe boom lock pin. Back tractor closer to 260 backhoe and use backhoe control levers to align backhoe frame with backhoe mounts on tractor. Use pins to secure backhoe to tractor: Use stabilizer control levers to raise or lower stabilizers as needed to position notches in backhoe frame above mount hooks. Reposition tractor hooks under notches. Use stabilizer control levers to lower stabilizers until notches rest in hooks.

Use boom control lever to rotate 260 backhoe to align top holes, and install pins. Check to be sure hydraulic hoses are routed away from pinch points. Remove backhoe swing lock pin. From the operator's seat, bleed the system by doing the following: Raise and lower stabilizers. Raise and lower boom. Extend and retract dipperstick. Curl and dump bucket. Swing boom from side to side. Install swing lock pin and boom lock pin. Park tractor safely. Bleed Hydraulic System - Run engine at low idle. Check to be sure operating area is clear. Operate control levers to move all cylinders several times until backhoe runs smoothly.

John Deere 1026R Mower Deck

54-inch Mower Deck Specifications

Model - 54D AutoConnect Mid-Mount Mower
Mower Type - Mulch or Side Discharge
Compatibility - JD 1026R
Cutting Blades - 3
Overall Width - 1.74 m (68.5 in.)
Overall Length - 1.75 m (69 in.)
Cutting Height - 2.5-10.2 cm (1-4 in.)
Cutting Width - 1.37 m (54 in.)
Mower Weight - 89 kg (197 lb.)
Blade Bolt Torque - 68 Nm (50 lb-ft.)
Gearbox Oil Capacity - 136 mL (4.6 oz.)

60-inch Mower Deck Specifications

Model - 60D AutoConnect Mid-Mount Mower
Mower Type - Mulch or Side Discharge
Compatibility - JD 1026R
Cutting Blades - 3
Overall Width - 1.85 m (72.8 in.)
Overall Length - 1.82 m (71.6 in.)
Cutting Height1 - 2.5-10.2 cm (1-4 in.)
Cutting Width - 1.52 m (60 in.)
Mower Weight - 117 kg (258 lb.)
Blade Bolt Torque - 122 Nm (90 lb-ft.)
Gearbox Oil Capacity - 136 mL (4.6 oz.)

Adjusting Deck Height - Ensure that the 60D mower deck is level. Raise the mower deck fully and measure the mower stop-to-tractor frame gap between the mower lift stop and the tractor frame. Compare the measurement to specification: Mower Stop-to-Tractor Frame Gap Distance - 3 mm (0.125 in.). If the mower stop-to-tractor frame gap is to specification, the deck adjustment is complete. If adjustments are needed beyond this point, perform the deck side-to-side and the front-to-rear procedures after the mower stop-to-tractor frame gap is successfully set. If the mower stop-to-tractor frame gap cannot be achieved, the rockshaft linkage and or the lift strap linkage are out of adjustment. If the mower stop-to-tractor frame gap is not to specification: Lower the 60-inch mower deck to the ground. Stop the engine and remove key.

Wait for the engine and all moving parts to stop before leaving the operator seat. Remove the retaining pins and pivot pin securing both turnbuckles to the lift arms. To reduce the gap, shorten the turnbuckle assemblies an equal number of turns. To increase the gap, lengthen the turnbuckle assemblies an equal number of turns. Install the turnbuckles on the lift arms. Raise the 60" mower deck fully, stop engine, and remove key. Measure the mower stop-to-tractor frame gap between the mower lift stop and the tractor frame. Compare the measurement to specification: Mower Lift Stop-to-Tractor Frame Gap (Distance) - 3 mm (0.125 in.). Repeat steps a - i until mower stop-to-tractor frame gap is to specification. Perform the side-to-side and the front-to-rear adjustment procedure.

John Deere 1026R Snowblower

54" Snow blower Specifications

Model - Frontier SB1154
Snowblower Type - Rear-Mounting
Compatibility - JD 1026R
Hitch Type - Category 1 iMatch
Steel skid shoes - Adjustable and replaceable
Cutting edge - Welded
Park Stand - Std
Chute type - 2 part
Chute deflector - Manual standard
Optional deflector adjustment - 3000 psi. (14647 kPa)
Chute rotation - Manual or hydraulic 245 deg.
Working height - 26 in. (660 mm)
Transport width - 54 in. (1372 mm)
Working width - 54 in. (1372 mm)
Length - 41 in. (1041 mm)
Roller chain - #60
Chain idler adjustment - Manual
Chute diameter - 8 in. (203 mm)
Auger diameter - 15 in. (381 mm)
Auger speed - 170 RPM
Impeller speed - 540 RPM
Impeller blades - 4
Impeller diameter - 24 in. (610 mm)
Tractor PTO speed - 540 RPM
Minimum tractor HP - 20 PTO HP
Maximum tractor HP - 40 PTO HP
Auger overload protection - Shearbolt
PTO overload protection - Shearbolt
Operating weight - 512 lbs (232 kg)
Shipping weight - 514 lbs (233 kg)

47" Snowblowers Specifications

Snow blower Type - Two-Stage, Front Mount
Compatibility - JD 1026R
Width - 120 cm (47-in.)
Height of Opening - 58 cm (23-in.)
Housing Thickness - 14 ga (0,075-in.)
Side Panel Thickness - 7 ga (0,177-in.)
Auger Diameter - 16-in. (41 cm)
Auger Speed - 160 rpm at rated engine speed
Impeller Speed - 800 rpm at rated engine speed
Impeller Diameter - 40,6 cm (16-in.)
Lift System - Hydraulic
Lift Height - 19-20 cm (7-1/2-8 in.)
Chute Control - Hydraulic
Chute Rotation - 200 Deg.
Weight (Approximate) - 181 kg (400 lbs)

54 Inch Snowblower Specifications

Snow blower Type - Front-Mounting
Compatibility - JD 1026R
Clearing Width - 1400 mm (54 in.)
Height to Top of Spout - 780 mm (30-5/8 in.)
Length - 690 mm (27 in.)
Lift Height - 280 mm (11 in.)
Net Weight - 113 kg (250 lbs)
Scraper Blade Reversible and Replaceable - 1300 mm (59-15/16 in.)
Discharge Chute Control - Hydraulic
Discharge Chute Rotation - 100 deg. to each side
Snowblower Drive - Splined coupler shaft to gear case
Snowblower Lift - Hydraulic
Rotor Length - 1000 mm (39-3/8 in.)
Auger Speed - 176 rpm
Auger Diameter - 406 mm (16 in.)
Impeller Speed - 950 rpm
Impeller Diameter - 403 mm (15.5 in.)
Drive - Gear case to roller chain
Bearings - Sealed ball bearings

John Deere 1026R Front Blade and Rotary Broom

60" Quick Hitch Front Blade Specifications

Compatibility - JD 1026R
Blade Width, Straight - 60 in. (1520 mm)
Blade Width, Angled 15 degrees - 58 in. (1470 mm)
Blade Width, Angled 27 degrees - 53.5 in. (1350 mm)
Angling Positions, Right and Left - 0-27 degrees
Blade Trip - Spring Trip
Blade Float - Hydraulic

60-inch Rotary Broom Specifications

Model Number - SW2160
Machine length - 69 in. (1750 mm)
Working width - 60 in. (1524 mm)
Working width at max angle - 55 in. (1397 mm)
Machine width - 72 in. (1830 mm)
Machine operating weight - 860 lb. (390 kg)
Corresponding power pack - HP2025
Loader attachment carrier - Current 300 series
Standard brush bristle materials - Poly
Brush diameter - 32 in. (810 mm)
Number of brush wafers - 34
Optional brush bristle materials - Combination poly/wire
Brush speed - 160 rpm
Angling range degrees - 23 left, 0 center, 23 right
Angling method - Hydraulic
Gauge wheels - Optional
Parking stands - Standard
Hydraulic relief valve protection - Standard
Dust deflector - Optional
Dust suppression system - Optional 60-gal. (227.12 L) water tank
Brackets system - Standard