________________________________________________________________________________

John Deere 3203 Attachments

John Deere 3203 Front End Loader

300 Loader Specifications

Type of Attachment - Front End Loader
Model - 300 Loader
Compatibility - JD 3203
Height (to pin) - 112.8 in. (286 cm)
Clearance, dumped bucket - 68 in. (172 cm)
Dump reach - 33 in. (83 cm)
Dump angle - 40.5
Reach at ground - 53.7 in. (136 cm)
Rollback at ground - 21
Rollback, raised - 101
Breakout force (at pin) - 1,728 lb (783 kg)
Breakout force (at 500 mm) - 1,229 lb (557 kg)
Breakout force (bucket) - 1,115 lb (505 kg)
Lift to full height (at pin) - 740 lb (335 kg)
Lift to full height (at 500 mm) - 547 lb (248 kg)
Lift to 1.5m (at pin) - 951 lb (431 kg)
Lift to 1.5m (at 500 mm) - 740 lb (335 kg)
Attachment style - hooks and lock pins
Raise time to height - 3.2 sec
Bucket dump time - 2.71 sec
Lowering time - 1.63 sec
Rollback time - 1.38 sec

300X Loader Specifications

Type of Attachment - Front End Loader
Model - 300X Loader
Compatibility - John Deere 3203
Height (to pin) - 90 in. (2,28 m)
Clearance, dumped bucket - 68,6 in. (1,74 m)
Dump reach - 30,4 in. (0,77 m)
Dump angle - 40
Reach at ground - 54,4 in. (1,38 m)
Rollback at ground - 21
Rollback, raised - 103
Breakout force (at pin) - 2855 lb (1295 kg)
Breakout force (at 0.5 m) - 2032 lb (921 kg)
Lifting (full height at pin) - 1360 lb (616 kg)
Lifting (full height at 0.5 m) - 999 lb (453 kg)
Lifting at 1.5m (at pin) - 1700 lb (771 kg)
Lifting at 1.5m (at 0.5 m) - 1312 lb (595 kg)
Bucket width - 61 in. (1,54 m)
Attachment style - Deere quick-attach
Raise time to height - 2,8 s
Bucket dump time - 4,1 s
Lowering time - 1,7 s
Rollback time - 1,7 s

John Deere 3203 Backhoe

447 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - JD 3203
Weight, With RSA Side Plate Kit and 20” Bucket - 469 kg (1035 lb)
Swing Arc - 180 degrees
Loading Height (bucket at 60°) - 1.99 m (78.5 in.)
Reach From Center Line of Swing Pivot - 3.15 m (124 in.)
Transport Height - 2.06 m (81 in.)
Bucket Rotation - 180 degrees
Loading Reach (bucket at 60°) - 1.09 m (43 in.)
Transport Overhang - 1.14 m (45 in.)
Undercut - 44 cm (17.5 in.)
Stabilizers Spread Width (Raised) - 1.55 m (61 in.)
Stabilizers Spread Width (Lowered) - 2.26 m (89 in.)
Boom Lift Capacity (see note below) - 270 kg (595 lb)
Dipperstick Digging Force - 909 kN (2005 lb)
Bucket Digging Force - 1288 kN (2840 lb)
Bucket Control Main Relief Valve Pressure - 15,51 MPa (2250 psi)
Digging Depth - 61cm (24 in.) flat bottom.
Bucket Width - 23 cm (9 in.)
SAE Struck Capacity - 0.014 m3 (0.49 ft3)
Heaped Capacity - 0.018 m3 (0.64 ft3)

Install Stabilizers - Pivot pins on 447 backhoe are installed with either cotter pins or retainers. Retainer is installed in pivot pin with bolt, 11/32-in. washer, and 5/16-in. locknut. Remove pivot pins stored in stabilizers. Remove retainers securing pivot pins to backhoe. Remove pivot pins securing cylinders to 447 backhoe, and remove cylinders. Install both stabilizers on backhoe with pivot pin. Install cotter pins or retainers in pivot pins. Install both cylinders on backhoe with pivot pin. Route all hydraulic hoses above the pivot pins. Install cotter pins or retainers in pivot pins. Install both cylinders on stabilizers with pivot pins. Install cotter pins in pivot pins. Lubricate all grease fittings and pivot points before operating backhoe.

Install Bucket - Grease both sides of two 1-1/32 x 1-1/2 in. washers and install between bucket and dipperstick on both sides of dipperstick if needed. Install pivot pin through bucket, washers, and dipperstick. Install two retainers in pivot pin with hardware. Remove shipping wire holding link to dipperstick. Pivot the bucket back and install pivot pin through bucket and link. Install two 1-1/32 x 1-1/2 in. washers between bucket and link if needed. Install two retainers in pivot pin with hardware. Lubricate all grease fittings and pivot points before operating backhoe.

John Deere 3203 Rotary Tiller

655 Rotary Tiller Specifications

Model - 655 Rotary Tiller
Compatibility - JD 3203
Cutting Width 1,2m (47 in.)
Tilling Depth 178mm (7 in.)
Skid Shoe Height Adjustment 30-75mm (1.2 - 3 in.)
Tine Cutting Diameter 372mm (14.5 in.)
Tine Shaft Speed 239 rpm
Final Drive Chain ASA 80 S
Gearbox Fluid Capacity 1L (2.2 pt)
Lateral Chaincase Fluid Capacity 1,250L (2.8 pt)
Weight (less slip clutch and joint) 182kg (401 lb)

665 Rotary Tiller Specifications

Model - 665 Rotary Tiller
Compatibility - JD 3203
Cutting Width 1,7m (65 in.)
Tilling Depth 178mm (7 in.)
Skid Shoe Height Adjustment 40 - 80mm (1.6 - 3 in.)
Tine Cutting Diameter 434mm (17 in.)
Tine Shaft Speed 264 rpm
Final Drive Chain ASA 100
Gearbox Fluid Capacity 1L (2.2 pt)
Lateral Chaincase Fluid Capacity 1,600L (3.6 pt)
Weight (less slip clutch and joint) 264kg (582 lb)

Checking and Changing Chaincase Oil - To add oil: Locate check plug on chaincase. Oil should be seen in check plug. Remove fill plug. Add gear oil until seen in check plug. If removed, install and tighten check plug to 25 Nm (17.5 lb-ft). Install and tighten fill plug to 25 Nm (17.5 lb-ft). Gasket must be replaced when chaincase cover is removed. To change oil: Remove fill plug. Loosen chaincase cover bolts to drain oil. Remove cover and replace gasket. Install cover and tighten bolts. Add gear oil until seen in check plug. If removed, install and tighten check plug to 25 Nm (17.5 lb-ft). Install and tighten fill plug to 25 Nm (17.5 lb-ft).

Replacing Tines - Support raised attachment with a mechanical stop or lower completely to the ground before servicing. Block 665 rotary tiller in raised position. Stand facing rotary tiller rear to identify tines: Left-hand tine curves to the left when the cutting edge is forward. Right-hand tine curves to the right when the cutting edge is forward. When replacing tines, note tine and hardware positions before removal. Remove one tine and install replacement before proceeding to the next tine. This will ensure the pattern and hardware configuration is
maintained. Remove nuts, lockwashers and bolts. Install replacement tine with cutting edge forward. Install bolts, lockwashers and nuts. Tighten to 95 Nm (70 lb-ft).