________________________________________________________________________________

John Deere 4105 Attachments

John Deere 4105 Front End Loader

300CX Loader Specifications

Type of Attachment - Front End Loader
Model - 300CX
Compatibility - John Deere 4105
Lift capacity at pivot pin (max. ht.) - 1,393 lb. (633 kg)
Lift capacity at 500 mm ahead of pivot pin - 1,005 lb. (457 kg)
Lift capacity to 59 in. at pivot pin - 2,109 lb. (959 kg)
Lift capacity to 59 in. at 500 mm ahead - 1,639 lb. (745 kg)
Max. lift height at pivot pin - 103.3 in. (2616 mm)
Reach at max. height - 30.1 in. (766 mm)
Breakout force at pivot pin - 3,769 lbf. (16 771 N)
Dump angle - 49.3 deg.
Rollback angle - 23.8 deg.
Loader raising/lowering time - 3.6/2.1 sec.
Bucket dump time/regen - 3/1.16 sec.
Bucket rollback time - 1.8 sec.

H165 Loader Specifications

Type of Attachment - Front End Loader
Model - H165
Compatibility - John Deere 4105
Lift capacity at pivot pin (max. ht.) - 1,393 lb. (633 kg)
Lift capacity at 500 mm ahead of pivot pin - 1,005 lb. (457 kg)
Lift capacity to 59 in. at pivot pin - 2,109 lb. (959 kg)
Lift capacity to 59 in. at 500 mm ahead - 1,639 lb. (745 kg)
Max. lift height at pivot pin - 109 in. (2767 mm)
Reach at max. height - 30.1 in. (766 mm)
Breakout force at pivot pin - 3,769 lb. (1710 kg)
Breakout force at 500mm - 2,665 lb. (1209 kg)
Dump angle - 49.3 deg.
Rollback angle - 23.8 deg.
Loader raising/lowering time - 3.6/2.1 sec.
Bucket dump time/regen - 3/1.16 sec.
Bucket rollback time - 1.8 sec.

Single Bale Spear Lift Capacity

Single Bale Spear Size (Diameter x Length), mm (in.) - 1219 x 1219 (48 x 48)
Single Bale Spear Orientation (From End) - 416 (916)
Rollback Capacity, kg (lbs.) - 474 (1043)

Triple Bale Spear Lift Capacity

Triple Bale Spear (Diameter x Length), mm (in.) - 1219 x 1219 (48 x 48)
Triple Bale Spear Orientation (From End) - 398 (877)
Rollback Capacity, kg (lbs.) - 459 (1009)

Attaching Ballast Box to Tractor with Three-Point Hitch - Back up tractor to ballast box with hitch points approximately in alignment. Engage tractor parking brake and/or place transmission in PARK. Shut off tractor engine and remove key. Attach tractor draft links. Fasten with quick-lock pins (stored on tractor draft links). Align center link with upper hole in ballast box mounting straps and install center link mounting hardware. Start tractor engine. Slowly pull hitch control leverto raise ballast box. Check for interference. Lower hitch to ground and adjust center link and/or lift links if necessary.

320R Loader Specifications

Type of Attachment - Front End Loader
Model - 320R
Compatibility - John Deere 4105
Bucket Width - 1550 mm (61 in)
Length - 633 mm (25 in)
Mass - 94 kg (207 lb)
Hydraulic System Rated Flow - 21.61 L/min (5.7 gal/min)
Maximum Pressure - 17 237 kPa (172 bar) (2495 psi)
Loader Raise Time - 5.30 sec.
Loader Lower Time - 3.10 sec.
Bucket Dump Time - 5.50 sec.
Bucket Rollback Time - 3.20 sec.
Lift Height (Maximum) To Pivot Pin - 2616 mm (103 in)
Bucket Level Clearance - 2411 mm (95 in)
Bucket Dumped Clearance - 2003 mm (79 in)
Overall Length - 3218 mm (127 in)
Digging Depth - 121 mm (5 in)
Reach At Maximum Lift Height with Bucket Dumped - 766 mm (30 in)
Bucket Reach on Ground with Bucket Leveled - 1491 mm (51 in)
Dump Angle - 49°
Dump Angle at Ground - 138°
Rollback Angle - 24°
Rollback Angle at Full Height - 112°
Lift Capacity To Maximum Height at Pivot Point - 633 kg (1393 lb)
Lift Capacity To Maximum Height - 457 kg (1005 lb)
Lift Capacity To 1500 mm (59 in) at the Pivot pin - 959 kg (2109 lb)
Lift Capacity To 1500 mm (59 in) - 745 kg (1639 lb)
Breakout Force At Pivot Point - 16 770 N
Breakout Force At 500 mm forward of the Pivot point - 11 860 N
Bucket Rollback Force At Maximum Height - 8650 N
Bucket Rollback Force At 1500 mm (59 in) Lift Height - 13 700 N
Bucket Rollback Force At Ground Level Line - 13 100 N

John Deere 4105 Backhoe

375 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 4105
Digging Depth - 7 ft 8 in
Reach From Swing Point - 10 ft 4 in
Bucket Rotation - 180 degrees
Swing Arc - 180 degrees
Stabilizer Width (Spread) - 7 ft 5 in
Boom Digging Force - 2005 lbs
Bucket Digging Force (lb) - 2840 lbs
Transport Height - 6 ft 9 in
Weight - 1035 lbs
Lift Capacity (lb) - 595 lbs
Valve spools - With machined metering grooves allow smooth operation and exact control of multiple functions
Buckets width - 12, 18, 24, and 36-in.
Hydraulic cylinders - Twin hydraulic cylinders, to control the swing
Swing system - With double-acting cylinders

375 Backhoe Troubleshooting

Backhoe does not operate: Low oil supply - Add oil. Hoses not properly connected - Check hose connections. Worn or damaged pump - Replace or repair pump. Broken line - Check for leaks, replace line.

Slow operation and poor Hydraulic System performance: Engine speed too low - Adjust RPM’s. Defective pump - Check pressure or replace. Load too heavy - Check line pressure. Faulty main relief valve - Clean or replace main relief valve. Internal valve crack - Replace valve section. Suction line filter plugged - Clean. Oil too heavy for cold weather use - Replace with lighter oil. Power supply may not be plumbing enough oil - Use a flow meter to check out whether 4-8 GPM flow rate is being achieved. Low oil level - Add oil. Pressure line restricted - Check for obstruction. Collapsed suction line - Check for damage. Valve spool not at full stroke - Check movement and linkage.

375 Backhoe does not hold up load: Cylinder seals leaking - Replace seals. Valve spool leaking - Replace seals. Oil bypassing valve spool - Replace valve bank.

Load drops when valve spool moved from neutral: Dirt in load check valve - Disassemble and clean.

Excess oil heat: Damaged or worn pump - Repair or replace. Too fast of an engine speed - Reduce throttle. Main relief bypass valve improperly set - Check relief setting. Draft control lever not all the way down - Position correctly.

Oil leakage: Valve spool seals - Replace seals. Loose hose fittings - Tighten just enough to stop leakage. Broken oil line - Replace hose or line.

John Deere 4105 Snowblower

48" Snow blower Specifications

Model - Frontier SB1148
Snowblower Type - Rear Mount
Compatibility - JD 4105
Hitch Type - Cat. 1 iMatch
Steel skid shoes - Adjustable and replaceable
Cutting edge - Welded
Park Stand - Std
Chute type - 2 part
Chute deflector - Manual standard
Optional deflector adjustment - 3000 psi. (14,647 kPa)
Chute rotation - Manual or hydraulic 245 degrees
Working height - 24.625 in. (625 mm)
Transport width - 48 in. (1219 mm)
Working width - 48 in. (1219 mm)
Length - 39 in. (991 mm)
Roller chain - #50
Chain idler adjustment - Manual
Chute diameter - 8 in. (203 mm)
Auger diameter - 15 in. (381 mm)
Auger speed - 170 RPM
Impeller speed - 540 RPM
Impeller blades - 4
Impeller diameter - 20 in. (508 mm)
Tractor PTO speed - 540 RPM
Minimum tractor HP - 16 PTO HP
Maximum tractor HP - 35 PTO HP
Auger overload protection - Shearbolt
PTO overload protection - Shearbolt
Operating weight - 420 lb. (191 kg)
Shipping weight - 422 lb. (192 kg)

John Deere 4105 Blade

60-inch Blade Specifications

Blade Model - Frontier RB2160
Type - Rear Mount
Compatibility - JD 4105
Hitch - Cat. 1 iMatch
Blade Frame - Formed steel channel frame
Cutting edge - 1/2" x 6" (1.26 x 15.1 cm) reversible
Angle/Pivot - 360 Degrees
Angle-Forward - 3, up to 53 degrees each side
Angle-Reverse - 3, up to 53 degrees each side
Moldboard thickness - 1/4" (0.63 cm)
Moldboard length - 60" (152 cm)
Moldboard height - 17" (42.9 cm)
Moldboard type - Progressive-formed
Moldboard upperedge - Full bend
Offset (or swing) - 6" or 12" (15.1 or 30.2 cm) left or right
Tractor maximum - 65 HP
Tilt - 3, up to 22 degrees up and down
Operating weight - 392 lbs. (179 kg)