________________________________________________________________________________

John Deere 4200 Attachments

John Deere 4200 Front End Loader

420 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4200
Bucket Width - 1350 mm (53 in.)
Bucket Length - 618 mm (24.3 in.)
Bucket Mass - 77 kg (169 lb)
Hydraulic System Rated Flow - 32.6 L/Min (8.6 gal/min)
Maximum Pressure - 14.6 MPA (2124 psi)
Maximum Lift Height To Pivot Pin - 2198 mm (86.5 in.)
Bucket Level Clearance - 2047 mm (80.6 in.)
Bucket Dumped Clearance - 1599 mm (63 in.)
Overall Length - 3119 mm (123 in.)
420 Loader Digging Depth - 152 mm (6 in.)
Reach At Max Lift Height - 593 mm (23.3 in.)
Bucket Reach on Ground - 1469 mm (57.8 in.)
Max Dump Angle - 41°
Max Dump Angle at Ground - 116°
Max Rollback Angle - 24°
Rollback Angle at Full Height (SAE) - 64°
Overall Height In Carry Position - 1321 mm (52 in.)
Lift Capacity To Max Height at Pivot Point - 456 kg (1003 lb)
Lift Capacity To Max Height - 344 kg (757 lb)
Lift Capacity To 1.5 m (59 in.) at Pivot Point - 598 kg (1316 lb)
Lift Capacity To 1.5 m (59 in.) - 567 kg (1247 lb)
Lift Capacity With Forklift to Max Height - 235 kg (518 lb)
Breakout Force At Pivot Point - 9522 N
Breakout Force At 500 mm (19.7 in.) Forward of Pivot Point - 6941 N
Bucket Rollback Force At Max Height - 10228 N
Bucket Rollback Force At 1.5 m (59 in.) Lift Height - 12560 N
Bucket Rollback Force At Ground Level Line - 10192 N

410 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4200
Height (to pin) - 74 in. (1,87 m)
Clearance, dumped bucket - 55,1 in. (1,39 m)
Dump reach - 24,8 in. (0,62 m)
Dump angle - 45
Reach at ground - 44,6 in. (1,13 cm)
Rollback at ground - 25
Rollback, raised - 64
Breakout force (at pin) - 2257 lb (1023 kg)
Breakout force (bucket) - 1661 lb (753 kg)
Lifting (full height at pin) - 882 lb (400 kg)
Lifting (full height at 0,5 m) - 618 lb (280 kg)
Lifting at 1.5m (at pin) - 1072 lb (486 kg)
Lifting at 1.5m (at 0,5 m) - 781 lb (354 kg)
Bucket width - 49,2 in. (1,24 m)
Raise time to height - 2,5 s.
Bucket dump time - 2,0 s.
Lowering time - 1,8 s.
Rollback time - 1,9 s.

Install Bucket or Attachment - Remove pin from each side of attachment holder. Roll top of bucket back and align hook with holder pin. Using lifting straps, raise front of loader high enough to allow pin to locate into holder strap on each side of attachment. Install pin into pin on each side of attachment.

Position 410 Loader to Mount on JD 4200 Tractor - Drive tractor to side of loader and shut off engine. Route hoses between loader boom and mounting frame (on tractor). Cut wires that fasten lift cylinders to masts. Move control lever(s) back and forth and side-to-side (if applicable) several times to relieve system pressure. Connect couplers matching color-coded caps on hoses and colors on coupler plate as outlined below: Red or Silver - Bucket Cylinder-Head End, Yellow - Bucket Cylinder-Rod End, Green - Lift Cylinder-Head End, Black - Lift Cylinder-Rod End. Place a minimum of 25 kg (55 lb) weight in the bucket before extending the lift cylinders. Extend lift cylinders to raise 410 loader into mounting position. Shut off tractor engine. Move control lever(s) back and forth and side-to-side (if applicable) several times to relieve system pressure. Disconnect couplers.

John Deere 4200 Backhoe

47 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 4200
Loading Height (bucket at 60 deg.) - 1800 mm (70 in.)
47 Backhoe Digging Depth - 2290 mm (90 in.)
Weight - 460 kg (1013 lbs)
Swing Arc - 180 deg.
Reach From Center Line of Swing Pivot - 2900 mm (114 in.)
Transport Height - 1800 mm (69 in.)
Bucket Rotation - 180 deg.
Loading Reach (bucket at 60 deg.) - 1090 mm (43 in.)
Transport Overhang - 1070 mm (42 in.)
Undercut - 760 mm (30 in.)
Stabilizers Spread Width (Raised) - 1550 mm (61 in.)
Stabilizers Spread Width (Lowered) - 2260 mm (89 in.)
Boom Lift Capacity - 245 kg (540 lbs)
SAE Dipperstick Digging Force - 8920 N (2005 lb)
SAE Bucket Digging Force - 12630 N (2840 lb)
Bucket Control Main Relief Valve Pressure - 15,51 mPa (2250 psi)

John Deere 4200 Snowblower

47-inch Snowblower Specifications

Type - Two-stage
Compatibility - JD 4200
Cutting Width - 47 in. (1.2 m)
Overall Cutting Height - 23 in. (584 mm)
Auger Diameter - 16 in. (406 mm)
Rotor Fan Diameter - 16 in. (406 mm)
Chute Rotation - Hydraulic
Drive - Mid PTO
Weight (Approx.) - 400 Ib. (181 kg)
Hydraulic spout rotation - 200 degrees
Worm-gear drive - With durable cast-iron housing
Skid shoes - Three-position skid shoes
Snow-deflector spout - Adjustable

John Deere 4200 Mower

60-Inch Mower Deck Specifications

Type - Mid-Mount
Compatibility - JD 4200
Cutting Width - 152.4 cm (60 in.)
Number of Blades - 3
Spindles - 25.4 mm (1.0 in.)
Weight - 147 kg (325 lb)
Gear Case Grease Volume - 240 ml (8 oz)
Input Shaft End Play - 0.0-0.06 mm (0.0-0.002 in.)
Output Shaft End Play - 0.0-0.03 mm (0.0-0.001 in.)
Blade Bolt Torque - 102-123 Nm (75-91 lb-ft)

72-Inch Mower Deck Specifications

Type - Mid-Mount
Compatibility - JD 4200
Cutting Width - 184.9 cm (72.8 in.)
Number of Blades - 3
Spindles - 25.4 mm (1.0 in.)
Weight - 203 kg (448 lb)
Gear Case Grease Volume - 0.5 L (1 pt)
Input Shaft End Play - 0.0-0.06 mm (0.0-0.002 in.)
Output Shaft End Play - 0.0-0.03 mm (0.0-0.001 in.)
Blade Bolt Torque - 102-123 Nm (75-91 lb-ft)

261 Mower Specifications

Mower Type - Rear Mount
Compatibility - JD 4200
Cutting Width - 152 cm (60 in.)
Cutting Height - 51-152 mm (2-6 in.)
Number of Blades - 3
Belt - B - Section
Gear Case Grease Volume 3-point Hitch Mower - 0.5 L (1 pt)
Mounting - Category 1
PTO Speed - 540 rpm
Weight - 168 kg (370 lb)

261 Mower Spindle Disassembly - Clamp lower hub of spindle assembly in a vise. Remove grease fitting. Remove nut. Loosen sheave. Be careful not to bend flanges. Remove sheave. Remove key and bushing. Press shaft from housing. Remove spacer. Remove bearing using a knife-edge puller. Inspect shaft for excessive wear or damage. If shaft or hub is not worn or damaged, it is not necessary to separate. To separate, hold shaft in a soft-jaw vise and remove hub. Use a 1-1/2-in. driver disk to remove upper bearing and seal. Be sure disk does not press on snap ring. Remove snap rings. Clean inside of housing with solvent. Be sure to remove all metal shavings and grit. Check for wear or damage in bearing seating areas; replace, if required.