________________________________________________________________________________

John Deere 5220 Specs

John Deere 5220 Engine Specifications

Model - 3029D, Naturally Aspirated
Factory Observed PTO Power - 33.8 kW (45 hp) at 2400 rpm
Maximum Engine Torque - 162 Nm at 1400 rpm
Cylinders - 3
Bore - 106.5 mm (4.19 in.)
Stroke - 110 mm (4.33 in.)
Displacement - 2.9 L (179 cu in.)
Compression Ratio - 17.8:1
Cylinder Firing Order - 1-2-3
Intake Valve Clearance - 0.35 mm (0.014 in.)
Exhaust Valve Clearance - 0.45 mm (0.018 in.)
Slow Idle Speed - 825 ± 25 rpm
Fast Idle Speed - 2625 ± 25 rpm
Operating Range Speed - 1600-2400 rpm
Injection Pump Timing Position - 18° BTDC (TimeTrac)
Electrical System - 12-Volt, Negative Ground
Battery Voltage - 12-volt
Cold Cranking Amps - 700 CCA / 950 CCA
Battery BCI Group Size - 31
Alternator-Straddle Mount - 40 amps / 60 amps

JD 5220 Power Take-Off

PTO Type (Standard) - Fully Independent PTO (540)
Operational - SyncShuttle hiftable 540/540E Independent
Clutch - Lever Operated
Engine-540E (SyncShuttle) Speed - 1700 rpm
Engine-540 Speed - 2400 rpm
PTO Shaft (Length) - 86 mm (3.4 in.)
PTO power (rated engine speed) - 46.16 hp [34.4 kW]
PTO fuel use (engine speed) - 2.8 gal/hour [10.6 l/hour]

John Deere 5220 Transmission

Standard Transmission - 9/3 CollarShift Transmission
Optional Transmission - 9/3 SyncShuttle, 9/3 SyncShuttle with shiftable 540/540E PTO or 12/12 PowrReverser
Lever Gear Selector
Manual Shift
Brakes - Hydraulic, Wet, Self-Adjusting, Self-Equalizing

JD 5220 Hydraulic System

Type - Open Center
Pump - Tandem Gear
Power Steering - Hydrostatic
Pump Displacement-Steering - 11.9 cu cm (0.73 cu in.)
Pump Displacement-Implement - 20 cu cm (1.22 cu in.)
Steering Flow Rate - 25.7 L/min (6.8 gpm)
Implement Flow Rate - 43.2 L/min (11.4 gpm)
Steering (Maximum) Pressure - 12 997-13 500 kPa (130-135 bar) (1885-1955 psi)
Implement (Maximum) Pressure - 18 995-19 692 kPa (190-197 bar) (2755-2855 psi)
Hitch Lift Capacity - 1530 kg (3374 lb)
SCV Flow Rate - 43.2 L/min (11.4 gpm)

Three-Point Hitch

Hitch Categories - 1 and 2
Top Link Sensing
Standard - Fixed Draft Links with Interchangeable Balls
Optional - Telescopic Draft Links with Interchangeable Balls
Lift Capacity at 610 mm (24 in.) Behind Hitch Balls Capacity - 1530 kg (3374 lb)

John Deere 5220 Capacities

Fuel Tank - 68 L (18 gal)
Cooling System - 9.5 L (10 qt)
Crankcase (including filter change) - 8.5 L (9 qt)
Transmission/Hydraulic System (Dry Clutch, CollarShift/SyncShuttle) - 38 L (10 gal) / 64 L (17 gal) Hi-Crop
Transmission/Hydraulic System (Wet Clutch, PowrReverser) - 43.5 L (11.5 gal) / 70 L (18.5 gal) Hi-Crop
MFWD Differential Housing Axle Oil - 5 L (5.2 qt)
Wheel Hub Axle Oil (Each) - 0.7 L (0.74 qt)
Assembly Axle Oil - 6.2 L (6.6 qt)

JD 5220 Dimension

Wheel Base (2WD/MFWD), mm (in.) - 2007 (79) / 2032 (80)
Overall Length Including Draft Links (2WD/MFWD), mm (in.) - 3543 (139.5) / 3606 (142)
Overall Width Outside Edge of Tires (55.8 in. Tread Setting), mm (in.) - 1763 (69)
Overall Width Rear Axle Flange-to-Rear Axle Flange, mm (in.) - 1455 (57)
Cab Width (Glass), mm (in.) - 1549 (61)
Cab Width (Across Fenders), mm (in.) - 1801 (71)
Cab Width (Cab Roof), mm (in.) - 1707 (67)
Ground-to-Cab Top, mm (in.) - 2477 (97.5)
Rear Axle Centerline-to-Cab Top, mm (in.) - 1877 (74)
Crop Clearance (2WD/MFWD), mm (in.) - 476 (18.75) / 349 (13.75)
Ground-to-Drawbar Top, mm (in.) - 419 (16.5)
Drawbar Thickness, mm (in.) - 33.0 (1.3)
Front Axle Centerline-to-Hood Top (2WD/MFWD), mm (in.) - 1003.3 (39.5) / 911.7 (35.5)
Turning Radius with Brakes (2WD/MFWD), mm (in.) - 2957 (116.4) / 3109 (122.4)
Turning Radius without Brakes (2WD/MFWD), mm (in.) - 3444 (135.6) / 3810 (150.0)
Shipping Weight (2WD/MFWD) - 2264 kg (4991 lb) / 2736 kg (6031 lb)

John Deere 510 Loader

Height (to pin) - 112 inches (284 cm)
Clearance, dumped bucket - 85.2 inches (216 cm)
Dump reach - 24 inches (60 cm)
Dump angle - 43
Reach at ground - 68 inches (172 cm)
Rollback at ground - 30
Rollback, raised - 115
Breakout force (at pin) - 4451 lbs (2018 kg)
Breakout force (at 800mm) - 2944 lbs (1335 kg)
Lift to full height (at pin) - 2200 lbs (997 kg)
Lift to full height (at 800mm) - 1500 lbs (680 kg)
Lift to 1.5m (at pin) - 3043 lbs (1380 kg)
Lift to 1.5m (at 800mm) - 2160 lbs (979 kg)
Bucket width - 61 inches (154 cm)